Q In the circuit shown if VT = 2 V and k =1.5 mA/V.s, then VGSQ , IDQ , and VosQ,%3Dare:15 V2ik Ohm1 uFVL1 oFVin2k Ohm1M Ohm22k Ohma.Iog = 1.026 mA, Vasa = 2.948 V, and Voso= 15.9 VOb.Ioa = 1.375 mA, Vaso = 3.25 V, and Vpso =7.75 VО с.Iog = 1.53 mA, Voso = 1.95 V, and Voso%3D5.9 Vd.Ioo = 2.120 mA, VesQ = 1.925 V , and Voso= 12.9 V%3D

First we will find drain current then we will find out voltage .

In the circuit shown if VT = 2 V and k = 1.5 mA/V.s, then VesQ, IDQ , and VosQ, are: 15 V 2k Ohm 1 uF VL k Ohm IM Ohm 2k Ohm loo = 1.026 mA, Veso = 2.948 V, and Voso = 15.9 V O b. log = 1.375 mA, Vaso = 3.25 V, and Voso = 7.75 V OC. Iog = 1.53 mA, Vaso = 1.95 V, and Voso = %3D 5.9 V d. loo = 2.120 mA, Vasa = 1.925 V, and Voso = 12.9 V

In the circuit shown if VT = 2 V and k = 1.5 mA/V.s, then VesQ, IDQ , and VosQ, are: 15 V 2k Ohm 1 uF VL k Ohm IM Ohm 2k Ohm loo = 1.026 mA, Veso = 2.948 V, and Voso = 15.9 V O b. log = 1.375 mA, Vaso = 3.25 V, and Voso = 7.75 V OC. Iog = 1.53 mA, Vaso = 1.95 V, and Voso = %3D 5.9 V d. loo = 2.120 mA, Vasa = 1.925 V, and Voso = 12.9 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A)- Why need Modulation:-
Outside the United States speed is measured in Kilometers per hour (km/h) rather than miles per hour (mph). Although the exact conversion from km/h to mph is 0.57, a conversion factor of 0.6 is generally used because it is easier to remember. For the reverse conversion a factor of 1.7 is normally used. Perform the following conversions using the approximate conversion factors. a. What is the speed in mph of an automobile on the German Autobahn traveling at 160km/h?
The photo is attached to answer the question.
Use the block diagram reduction please
Q2) What is Grounding.? And Why Ground.?
INFE242 ELECTRONICS PLEASE i begging you help me in this problem ?? Please make it clear ALL thank and appreciation ?? ?
In a CE configuration, the voltage gain is __________ . a.always positive b.negative c.almost zero d.very low
Give some examples of electrical plan of a existing company.
Thank you.
Draw the pin diagram of 8051 & 8237 and write down the difference between them.
In a Common Base (CB) configuration, the current gain is _____________. a.infinite b.almost no gain c.High d.very High