I need help In the circuit shown below, Write thenode equation of Voj20V.-j5016-j12010014-148VSelect one:a. {Vo + (16 - j12)}/ j2 +{Vo/10} + {Vo + (-14 - j48)}/ -j5= 0b. {Vo - (16 - j12)}/ j2 +{Vo/10} = 0c. {Vo - (16 - j12) }/ j2 +{Vo/10} + {Vo - (-14 - j48)}/ -j5= 0d. None of these

Answered: Image /qna-images/answer/9228ea82-8843-4bd2-b279-ea8fe9096362.jpg

In the circuit shown below, Write the node equation of Vo V. -j50 16-j120 100 -14-j48 V Select one: a. {Vo + (16 - j12)}/ j2 + {Vo/10} + {Vo + (-14 - j48)}/ -j5 = 0 b. {Vo - (16 - j12)}/ j2 + {Vo/10} = 0 c. {Vo - (16 - j12) }/ j2 + {Vo/10} + {Vo - (-14 - j48)}/ -j5 = 0 d. None of these

In the circuit shown below, Write the node equation of Vo V. -j50 16-j120 100 -14-j48 V Select one: a. {Vo + (16 - j12)}/ j2 + {Vo/10} + {Vo + (-14 - j48)}/ -j5 = 0 b. {Vo - (16 - j12)}/ j2 + {Vo/10} = 0 c. {Vo - (16 - j12) }/ j2 + {Vo/10} + {Vo - (-14 - j48)}/ -j5 = 0 d. None of these

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the following zener clipper draw the output waveform Vz1 = 5V, Vz1 = 7V VK = 0.8v lkn ISV V₁₂ 5V 2, 72. -5V Q2 Determine The Output Waveform And Calculate The current and PIV 1kQ 1kQ 10 V 10 si www www Q. For the circuit shown in Figure below (1),find the maximum and minimum values of zener diod current. Live 5 ΚΩ www I IL 15 80-120 V 10 ΚΩ LIR 101 102 1015 S Ne 1 k0 www Iz 50 V U2 -ot V. Fumal inash
4- Design a boost converter that will have an output of 60 V from a 24-V source. Design for continuous inductor current and an output ripple voltage of less than one percent. The load is a resistance of 50 2. Assume ideal components for this design. VL ooooo ip - ^
An unipolar PWM full bridge circuit has a Vr.rms of 125V at a duty cycle D1 of 0.7. What is Vd? What is Vo.rms?
S-4) The input signal Vin of the clipper circuit given below is a sinusoidal signal of Vp-p = 30V and the wave the form is as given in the figure. a) Plot the output waveform of this circuit in the area given for + and - alternans. b) Calculate the peak values of the output and indicate it on the graph. Note: Diode threshold voltage will be 0.7V
8. Determine the output voltage V, and the Zener diode current Iz for the circuit below. The Zener diode is IN5236B. }} a) E-21 V, R1=1 km2, and R2-2 km2 b) E-21 V, R1-2 k2, and R2-1 k E R₁ www R₂
a2/a-Design Circint as the following peseripton: A. the positive cycle of the vout signal is 3.2 and Neyatine cycle is 4.3 (Note: we must used preetical Diodes aned vin is tov) B- the pesitive cycles of vout is s-3 od Negative cycle is (5 4) [te:Comsider vin = 1ovavd we must used Capaetor with praeticul Didde)
Q6. What is the purpose of harmonic standards? Provide a summary of comparison of IEEE and IEC standards. Write the purpose of the following international standards shown in Table- 2: [12] Table-2 Sr No 1 IEEE-18 Standards Description 2 IEEE 518 3 IEEE 519 4 IEEE 1159 5 IEEE P1433 6. IEEE P1453 7 IEEE P1564 8 IEC61000-3-2 9 IEC 61000-4-7 10 IEC 61642 11 IEC SC77A/WG9 12 IEC SC77A/WG2
2. Shunt regulator of Figure uses a Zener whose voltage is 5.1V at a current of 10mA, and rz-892. The diode is fed from a supply V=15V (nominal voltage) and R=0.5KQ a) Calculate Vzo. Find Vo with no load and V' at its nominal value. b) Find the change in Vo resulting from a ±1V change in V". c) Find the change in Vo resulting from connecting a load resistance RL that draws a current I1=ImA. d) Find Vo when R₁-0.2KQ. Is the Zener still operating in the breakdown region? mi Zanar ve
Vps = 10 V R = 0.1k02 ww -ovo R₁. Consider the Zener diode circuit shown in figure. The Zener diode voltage is Vz= 5.8V at Iz= 10mA and the Zener resistance is rz = 200. a) Find the output voltage for RL = 1k0 b) Find the change in the output voltage when the load resistance varies +ARL.
R2=1kiloOhm, Voltage Source=10Vpk at 1kHz frequency, R3=1kiloOhm and zener diode has 5V breakdown potential R1 www 1k0 D1 Vo V1 5V 10Vpk 1kHz R2 1k0 a.) Plot the Output Waveform Vo. b.) Explain the output waveform at + input cycle. c.) Explain the output waveform at - input cycle.
quations. 3. What are the advantages and disadvantages of a dual slope ADC? a blecL mation
Q2 In the circuit as shown below. Determine the (ripple factor) and sketch vp(out) for the filtered bridge rectifier with a load as indicated. 2 : 1 D3 D1 120Vp-p f= 50HZ + Output V1 V2 D2 D4 1uf R1=2k