In the circuit shown below, load current la equals to 50 2-30Q 415 V n 50 Z-30Q. 50 Z-30Q I. b 4.8 2 30° A O 9.6 z 30° A O 9.6 2 -30° A O 4.8 2 -30° A

Q: what is ON1 and SS1 is it a single component?

A: The above question is related to switching components in an impulse generator circuit.

Q: Vcc = 24 V R = 36 kn Rc = 1.8 kn Cout B = 150 Cin R = 3.6 Vin = 25 mV, R, = 3.3 kn RE = 220 N P-p CE

A: We need to find out the emitter resistance and voltage Gain and output voltage .

Q: Question 13 For the circuit shown, the following mesh currents are given: IA = 1.24Z71.2° A IB =…

A:

Q: ip Lp = 50 mH moo ell N₂ = 20 N₁ = 80 Lg k=0.8

A: The value of the primary induced voltage at the rate of 0.08Wb/s.Given:

Q: What are the three bias levels and VEE in the circuit shown if the design ischanged to have VL =…

A: Calculating bias voltage Calculating voltage VBL By applying KVL

Q: 2. Determine the Q-point for the following circuit and draw the DC load line, assume ẞx=150. R w www…

A: Drawing the DC Load Line.VCE​ = 0: IC=15V/3kΩ = 5mAIC= 0: VCE =1 5V

Q: Q + V IN R VIN OV C VIN R OV VIN Q = fi dt = f VIN dt =Vour = - dt OUT CR R

A: Given :    In this question they have mentioned a integrator circuit.     The output of integrator…

Q: In order to obtain a continuous output vo tage in step up chopper, a high value of capacitor is…

A: Choose the given statement is it true or false?  The given statement In order to obtain a continuous…

Q: input ou tpu D. 2. sing the following subsystem S x[n] yen] consider the following global system…

A:

Q: For a certain JFET, IGSS = 12.49 nA at VGS=6.86 V. The input resistance in MQ is %3D

A:

Q: c) Determine the output voltage Vout of the circuit shown in figure 10 n 2 ka 2 mvo s kn ww 4kn 15…

A: The solution is given below

Q: 3. Refer to the graphics addendum (C). What is the phase voltage at the Load?

A:

Q: Solve for Rc of Figure 42. 12 V - Vc = 6V www Ra www Rc VCE B=80 IB = 40 μA Reference: Boylestad, R.…

A: Given the value of β=80 Consider the value of the collector voltage. Vc=Vce=6 V

Q: 2. Consider the circuit shown in Figure 2 below, with Vs = 50Z 30° V, Is=22-20° A, R = 100 2, and Zc…

A: In this question We need to determine the value of Rx  for such power is maximum to the load Rx.  We…

Q: For the circuit shown, what is the Norton equivalent current, IN? j3 N 12Ω 2452.6° A -j5 N 14430° V…

A: In this question we will find Norton current..

Rectangular Coordinate System

In a rectangular coordinate system, each point based on the pair of coordinates is specified uniquely in the plane. From two fixed perpendicular lines, these coordinates are at a distance in the rectangular coordinate system. Each line is known as the reference axis and axes as plural. The point where they meet is called the origin (0,0).