In the circuit shown below = 83.0 V, R5 = 4.00, R3 = 2.00 2, R₂ = 2.20 2,15= 8.10 A, 4= 5.90 A, and ₁=13.2 A. Find the current through R₂ and R3, and the values of the resistors R₁ and R4. 12 = 13 = R₁ = R4 = R₁ A A aa Ω R₂ ww R₂ ww www.

Q: PROBLEM 4 Find Req R2 R3 120 R4: 60 R5 R7: 30 60 R1 120: Reg R6 180 Figure 4

A:

Q: R3 R, R5 R6 R R7 R4 R3, = R6, = R9 = 50 R2, = R5, = R8 = 42 R1, = R4, = R7 = 20

A:

Q: Use Multisim Schematics to create the voltage divider circuit in Figure 2. Run the simulation to…

A: The given circuit isWe need to measure the voltage across each resistor (i.e V1, V2 and V3) and the…

Q: How would you find total Resistance. I found Ra of R7,Rload, and R8 to be 12kOhms. Rb of R6 and Ra…

A: R7, Rload and R8 are series, Ra = 2 + 4 + 6 = 12 kΩRa and R6 parallel, Rb = 12 * 6 / (12 + 6) = 4…

Q: For given value of the circuit, Vsupply = 120 V, and with R₁= 2002, R₂-30.0, R3=75, R4=300, R5=…

A: The required parameter can be calculated by using mesh analysis and ohms law. By using the mesh…

Q: RL series has two resistors and two inductors. The Z of the circuit is 1000 ohms. The XL of the…

A: In this question , RL series circuit has resistors and inductors... Inductors values are given and…

Q: The superposition technique can be described as a multi-step process of calculating the individual…

A: The superposition technique involves analyzing a linear circuit by considering the individual…

Q: I need to solve for R3 not the voltage across R3

A: Voltage across R3 resistor is Vo:∵R1,R2andR3 is in SERIES connection:=> There are same current…

Q: Employing the characteristic curve in Figure 1 and obtain the design for a voltage divider…

A: As per company honor code, Since you have posted a question with multiple sub-parts, we will solve…

Analysis of Diode

It is a semiconductor device in electronics applications where only a one-way current is required. It is like a one-way switch that allows current to flow in one direction only. A diode has two terminals, a cathode, and an anode. The cathode is the negative terminal that carries electrons, while the anode is the positive terminal that carries holes. Although no element has holes, it just means that there is a free space for electrons. Diodes are used to convert AC to DC. As we know, AC shifts between positive and negative cycles and DC stays positive constantly. As the diodes allow current only in one direction, they filter out the AC signal’s negative cycle and only keep the positive one.

Working and Construction

In civil engineering, construction means the application of principles of science and mathematics for building bridges, dams, buildings, roads, highways, tunnels, airports, structures, etc. Different branches of science, like physics and chemistry, are extensively applied to design and analysis in construction. Material properties, the science of atmospheric conditions (like solutions, mixtures, etc.), the impact of environmental factors like, corrosion and acidity are some of the primary knowledge of chemistry which are used by civil engineers to carry out construction. Estimation of forces, application of laws of mechanics, fluids mechanics, soil mechanics, etc. are some of the fundamental concepts of physics, which are well applied in construction works. Building construction and structural engineering are two of the most primary areas in civil engineering that parallelly applies principles of both chemistry and physics to carry on construction works.

Property of Diode

An electronic component that facilitates the directional flow of current is known as a diode. According to the direction of the flow of current, the resistance of a diode changes from zero to Infinity.