In the case of an elevator, which of the following factor(s) describe the dynamic response.   A. A displacement between the floors on stopping   B. Elevator at the selected floor   C. Elevator getting stuck in the middle of the floor   D. A fast drop from one level to the next   E. A slow start from

Q: Water flows through a pipe having an inner radius of 20mm at the rate of 42 kg/hr at 20^OC.…

A: Given data Mass flow rate = 42 kg/hr  Radius (R) = 20 mm  Viscosity = 0.001 kg /ms

Q: The wheels of the refrigerator of the figure are stuck and will not turn. The refrigerator weighs…

A:

Q: A block in the following figure is pulled up with a Force 20 +S Nt. The weight of the block is 10…

A: WE HAVE GIVEN FORCE =20+S N WEIGHT OF BLOCKW=10 N CONTACT SURFACE AREA=10CM2 thickness of film=1mm

Q: A fluid flow is represented by the velocity field = ax + ay 1, where a is constant. The equation of…

A:

Q: A physics book slides off a horizontal tabletop with a speed of 1.1 m/s. It strikes the floor in…

A: Following are the given information. Book's horizontal velocity = 1.1 m/s t = 0.48 sec (when the…

Q: A commercial airliner with four jet engines, each producing 71 kN of forward thrust, is in a steady,…

A: Given: Three force applied on aeroplane.  Required : A single resultant force

Q: Q1: A reducing elbow is used to deflect water flow at a rate of 30 kg/s in a horizontal pipe upward…

A: From the figure, the inlet is taken as section (1) and outlet is taken as section (2). It is…

Q: At time t= 0 a small ball is projected from point A with a velocity of 112 ft/sec at the angle 55°.…

A: Initial velocity = 115 ft/sec Taken g = acceleration due to gravity = 32.174 ft/s2

Q: A three-legged tube is filled with oil (SG = 0.88). As shown, the surfaces of oil in all legs are at…

A:

Q: An overhead view of part of a pinball game is shown. If the plunger imparts an initial speed of 2.9…

A: The given figure is shown below:

Q: The water from a fire hose follows a path described by y=4.0+04x-0 20x (units are in metres). If v…

A: The path followed by the water jet is y = 4+0.4x-0.2x2 Also, the x component of velocity is constant…

Q: The branching of a blood vessel is shown. Blood at a pressure of 100mg Hg (13.3kPa) flows in the…

A: Given data  Discharge  Angle Diameter  We will use make of Momentum equation to solve this question.…

Q: lock is 10 Nt. The area of the contact surface between the bilock and fluid is 10 m². (27) Nt 1mm 30…

A: Given dataA=10cm2=10×10-4m2, μ=0.2 Nsm2,dy=10-3mShear force Fs=27- Psin30°=27-10×0.5=22 NThus Shear…

Q: The water jet is ejected from the 4-in.-diameter pipe with a steady velocity of v = 20 ft/s. It…

A:

Q: A ride in an amusement park consists of a rotating arm AB having a constant angular velocity wAB = 2…

A:

Q: The figure below shows a mobility Nyquist plot representing the response of a single mode. The three…

A: Given: ωA=500/51 radsωB=10 radsθA=13πradθB=13πradα=3

Q: A fluid is between two parallel horizontal plates as depicted above. The bottom plate is stationary…

A: Velocity gradient is the change in velocity per unit length/(Or height) in a fluid

Q: A ride in an amusement park consists of a rotating arm AB having a constant angular velocity wAB =3…

A:

Q: Bernoulli’s equation and represents the sum of velocity head, pressure head and the elevation head…

A:

Q: As shown in Figure, a stone is thrown vertically into the air from the top of tower 100 ft. high. At…

A:

Q: At the exit of the siphon, the velocity of water

A: Given, Determine the velocity of water, At the exit of the siphon ?Where, Siphone is used to drain…

Q: Determine the moment created by the weight of the traffic light about point O. The dimensions of the…

A: We have the arrangement as:

Q: a constant two-dimensional velocity field: a constant, incompressible, two-dimensional velocity…

A: Question is based on the 2D flow of fluid . Velocity equation of flow are given in the question…

Q: Air flows past an objects and exits as a free jet as shown in the figure. Because of the…

A: Consider a differential element of area. Calculate the discharge through it and then integrate it…

Q: Oil (kinematic viscosity, Voil = 1.0 × 105 m²/s) flows through a pipe of 0.5 m diameter with a…

A: Given: Kinematic Viscosity of Oil νoil=1.0x10-5m2/s, Diameter of pipe Doil=0.5 m, Velocity of oil…

Q: A horizontal water jet driven by an orifice is impinging on a vertical wall as shown in Figure 2.…

A: Fresistance = 900KN   Diameter = d = 10cm

Q: Determine the speed of the block shown in the figure at B. 6 m/s A B

A:

Q: Problem 3: Find the vertical movement and the rotation at point "c" W a b с L/2 L/2

A:

Q: The board rests on the surface of two drums. At the instant shown, it has an acceleration of 0.44…

A: Given that, Acceleration of drum tangential direction (at) = 0.44 m/s2 Acceleration of outer rim of…

Q: A block having a mass of 50 kg is subjected to a horizontal force that is causing it to have an…

A:

Q: ОА 3 A 4 m 5 4 100 m B

A:

Q: The sphere of diameter 0.02 m falls in a fluid of kinematic viscosity of 10 stokes with the terminal…

A: Diameter of sphere = 0.02 m Kinematic Viscosity = 10 stokes Terminal velocity = 0.02 m/s

Q: Question 8 In a two-dimensional field the velocity of fluid flow is given by v = (y³ - 5x²y)i +…

A:

Q: A trolley as shown in Figure E3.1 starts moving towards right with constant acceleration 0.25 m/s?.…

A:

Electrical Plans

An electrical plan is also known as an electrical drawing or a wiring diagram. It is a kind of visual representation which bears the blueprint symbols of all the electrical components in electrical house plans or various building construction projects. In other words, electrical plans describe electrical circuits and systems that build up the electrical house plans or building plans. An electrical engineer who works on various construction projects creates an electrical drawing. The engineer outlines the electric planning with different symbols and lines forming a detailed electrical circuit. These drawings are a means of representation for the clients, who will carry out the actual wiring process. In a nutshell, an electrical plan showcases the circuitry with the proper placement of electric components.