17) Consider a carwash application, where the electrical circuit includes several differenttypes of circuit logic (e.g. could be AND, OR, NOT, NAND, NOR). The circuit logic can bedeveloped by hard-wiring switches or by connecting the switches to digital logic gatesthat can be used to develop the circuit logic.PHOTOELECTRICWET-DOWNMAINCONTROLPANELAREA-PHOTOELECTRICS1-S2WHEEL PULLERPB1PB2-SOAPAREAPHOTOELECTRICWASHAREASOAP AREAEMERGENCYSTOP$5RINSEAREA-PHOTOELECTRICS3DRYAREA-WHEEL-PULLERMOTOR STARTERPHOTOELECTRICS4PHOTOSWITCH 5DRYEROVERRIDESWITCH-WASH AREAEMERGENCYSTOPHEATINGCONTACTORM2DRYER BLOWERMOTOR STARTER In the car wash circuit, photo switch 5 and the drier override switch are used to control the dry area.A digital logic gate could be used to produce the same circuit logic at this point in the circuit. Drawa digital logic gate that can be used to produce the same circuit logic and connect photo switch 5and the dryer override switch to the gates input.+5VDCPhotoswitch 5DryerOvervideSwitchfrom logicGateTo DryerCircuit

Given a car wash circuit photo switch 5 and dryer override switch are used to control the dry area.…

In the car wash circuit, photo switch 5 and the drier override switch are used to control the dry area. A digital logic gate could be used to produce the same circuit logic at this point in the circuit. Draw a digital logic gate that can be used to produce the same circuit logic and connect photo switch 5 and the dryer override switch to the gates input. +5VDC Photo Switch 5 Dryer Overvide Switch from logic Gate To Dryer Circuit

In the car wash circuit, photo switch 5 and the drier override switch are used to control the dry area. A digital logic gate could be used to produce the same circuit logic at this point in the circuit. Draw a digital logic gate that can be used to produce the same circuit logic and connect photo switch 5 and the dryer override switch to the gates input. +5VDC Photo Switch 5 Dryer Overvide Switch from logic Gate To Dryer Circuit

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

14. Modified sin wave inverter is more suitable for health facilities Solar systems a. Yes b. No c. Nor Yes or No
5
Draw the circuit for the following, and write the pin numbers for each gate. 1. Half Adder using XOR gate and AND gate. 2. Full Adder using the previous circuit with another Half Adder.
6. Modify your experiment circuit so that it appears as shown in Figure 3.2. One logic input will come from SW1. The other logic input will be a 1Hz clock (CLK) signal from the FUNCTION GENERATOR. You will monitor the gate output with LED DISPLAY L1 and the clock output on LED DISPLAY L2. + 5V 1K SW1 CLK LED INDICATOR (1Hz) Figure 3.2 7. Set SW1 to Binary 0 (down). Note the output on L1. Then set SW1 to binary 1(up). Again note the output on L1. Explain your result, SW1 = 0; Output C = SW1 = 1; Output C = What logic function does this gate performing? 12 V 10 k Ohm IN4001 SW1 OUTPUT INPUTS IN4001 sw2 Figure 3.3 8. Construct the logic gate shown in Figure 3.3. (note for the -12V supply and the 10K resistor). Again, DATA SWITCH SW1 and SW2 will supply the logic input D and E, and you will measure the output voltage at F with a voltmeter.
Determine the LED “on” current for the circuit above. Assume the logic “on” voltage is 5 volts, V(LED) = 2.0 volts and VCE(sat) = 0.4V.
What is the name for the circuitry that can be added to a cascaded or ripple adder to allow it to operate in parallel?
For some program, machine A has a clock cycle of time 5 ns and CPI is 1.5 whereas machine B has a clock cycle of time 15 ns and a CPI of 1. Which machine is faster and by how much?
Question 3
Write about fault tolerance.
In which type of fault diagnosis the fault can be identified by PCB testing ? a. Replacement b. Physical Testing c. Half split technique d. Dynamic Testing
Book used is Digital Logic with Verilog Design by Brown & Vranesic. Study the counting circuit diagram below and answer the following questions: a. Based on the circuit drawing, is the Clock Positive-Edge Triggered or Negative-Edge Triggered? b. How was this determination made? c. What are the minimum and maximum valkues of the circuit? Explain. d. There are 3 grayed out boxes we refer to this symbolic use as _____________. Why are these used in circuit design?
Discuss the concept of "circuit breakers" in microservices architecture and their significance in fault tolerance.