In process industry during a daily production run, a total of five (05) samples are collected with four (04) observations within each sample. The sample means (X-bar) are; 14.09, 13.94,16.86, 20.00, and 16.64 respectively. The corresponding ranges are; 9.90, 7.73, 4.41, 7.56, and 3.49 respectively. The lower and upper control limits of the x-bar chart are respectively O a. 11.44, 20.66 O b. 11.29, 20.65 O c. None is correct Od. 11.47, 21.14 e. 11.47, 16.55

In process industry during a daily production run, a total of five (05) samples are collected with four (04) observations within each sample. The sample means (X-bar) are; 14.09, 13.94,16.86, 20.00, and 16.64 respectively. The corresponding ranges are; 9.90, 7.73, 4.41, 7.56, and 3.49 respectively. The lower and upper control limits of the x-bar chart are respectively O a. 11.44, 20.66 O b. 11.29, 20.65 O c. None is correct Od. 11.47, 21.14 e. 11.47, 16.55

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

4. For a certain drilling machine of the Putnam Manufacturing Company, control limits foran x−Chart have been determined as: UCLx = 86.8 and LCLx = 83.3 (a) Sample averages for the most recent six samples, in sequential order, are 83.2, 83.9,84.7, 85.4, 85.9, and 86.7. What should be concluded about the process average?Should some action be taken? Why or why not? (b) What would you conclude (and why) about the process average if the sample averagesfor the most recent six samples, in sequential order, were 85.6, 84.9, 86.2, 85.2, 85.5,and 85.1?
A quality inspector took five samples in five hours, each with four observations, of the length time for glue to dry. The analyst compute the mean of each sample and the computed the grand mean. All values are in minutes. Use this information to obtain three-sigma control limits for means. It is known from previous experience that the standard deviation of the process is 0.02 minutes. Draw a control chart Please provide a step-by-step solution
In a fabric manufacturing factory, the quality control process using control charts from SPC. In an hour there are a total of 5 samples are taken each having 4 observations regarding the thickness of fabric in measured in millimeters. In a particular hour, the sample means (X-bar) are noted to be: 172.11,219.58, 208.24, 112.44, and 123.30 respectively. In the same sample, the corresponding ranges are: 13.17, 13.38, 15.34, 13.04, and 13.02 respectively What are the lower and upper control limits for the R chart? O a. 0,31.47 O b. 0,30.99 Oc. None is correct O d. 0,29.17 O e. 0,31.17 O f. 0,28.17
Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must be controlled. From sample sizes of 5 pistons produced each day, the mean and the range of this diameter have been as follows: Day Mean (mm) Range R (mm) 158 4.3 151.2 4.4 155.7 4.2 153.5 4.8 156.6 4.5 What is the UCL using 3-sigma?(round your response to two decimal places). 1. 2. 4.
Given there are five (05) sample taken. The sample means (X-bar) are; 15.36,14.61,16.36,20.28, and 15.77 respectively. Also, the corresponding ranges are; 10.79, 8.37,2.81,8.17, and 3.31 respectively. If the upper control limit for X-bar chart is 21.36, what should be the most appropriate the sample size? O a. 4 O b. 3 O d. 5 O e. None is correct NEXT PAGE GE
Answer quickly please ?
Twelve samples, each containing five parts, were taken from a process that produces steel rods at Emmanual Kodzi's factory. The length of each rod in the samples was determined. The results were tabulated and sample means and ranges were computed. The results were: Sample Sample Mean (in.) Range (in.) Sample Sample Mean (in.) Range (in.) 1 9.602 0.033 7 9.603 0.041 2 9.602 0.041 8 9.605 0.034 3 9.593 0.034 9 9.597 0.027 4 9.606 0.051 10 9.601 0.029 5 9.599 0.031 11 9.603 0.039 6 9.599 0.036 12 9.606 0.047 Part 2 For the given data, the x double overbarx = 9.6013 inches (round your response to four decimal places). Part 3 Based on the sampling done, the control limits for 3-sigma x overbarx chart are: Upper Control Limit (UCL Subscript x…
A process that is assumed to be in control with limits of 88 ±4 had sample averages for the x-bar chart of the following: 87.1,87, 87.2, 89, 90, 88.5, 89.5, and 88. Which of the following statement below are correct? a. Process mean is out-of-control b. Not enough information to determine С. Process mean is NOT out-of-control O d. None is correct
Cartons of Plaster are supposed to weigh exactly 32 ounces. Inspectors want to develop process control charts. They take five samples of six (6) boxes each and weigh them. Sample means (X-bar) are: 33.8, 34.6, 34.7, 34.1, and 34.2 respectively. Also, the corresponding ranges are: 1.1,0.3, 0.4. 0.7, and 0.3, respectively. The lower and upper control limits of the xbar-chart are respectively O a. None is correct O b. 30.11 and 40.15 O c. 34.01 and 34.55 O d. 33.12 and 34.12 O e. 37.01 and 39.23
54 Boxes of Honey-Nut Oatmeal are produced to contain 14.0 ounces, with a standard deviation of 0.20 ounce. For a sample size of 64, the 3-sigma X chart control limits are: Upper Control Limit (UCL) = ounces (round your response to two decimal places).
A manager wishes to build a control chart for a process. A total of five (05) samples are collected with five (05) observations within each sample. The sample means (X-bar) are; 15.36, 14.61. 16.36, 20.28, and 15.77 respectively. Also, the corresponding ranges are; 10.79,8.37,4.81, 8.17, and 3.31 respectively. The lower and upper control limits of the x-bar chart are ,respectively O a. 16.55, 11.47 Ob. 12.40, 19.72 Oc. 12.36, 20.59 Od. 18.55, 13.47 De. None is correct
Please show all work