In pipe flow, the horsepower of the pump can be computed as a function of a. The pressure head and the energy of the pump O b. The discharge and the total head loss O c. All of these O d. The discharge and the energy of the pump The elevation head and energy of the pump

In pipe flow, the horsepower of the pump can be computed as a function of a. The pressure head and the energy of the pump O b. The discharge and the total head loss O c. All of these O d. The discharge and the energy of the pump The elevation head and energy of the pump

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 24-in. pipe conducts water from reservoir A to a pressure turbine, which discharges through another 24-in. pipe into tailrace B. The loss of head from A to 1 is 5 times the velocity head in the pipe and the loss of head from 2 to B is 0.2 times the velocity head in the pipe. If the discharge is 25 cfs, (a) What is the head extracted, he, (ft) by the turbine? (b) What horsepower is being given up by the water to the turbine? El 200 ft El 15 ft 24-in. pipe El O ft 24-in pipe
P.2.7 The Power (P) required to drive the pump depends upon the diameter (D), the angular velocity (0), the discharge (Q), and the fluid density (p). Drive expression for (P) by dimensional analysis. Ans. P o'p D' .
A pump draws water from a reservoir A and lifts it to reservoir B as shown. The loss of head from A and lifts it to reservoir B as shown. The loss of head from A to (1) is 5 times the velocity head in the 12-inch pipe and the loss of head from (2) to B is 23 times the velocity head in the 7-inch pipe. Compute the pressure heads (2) in ft when the discharge is 447 gpm. Round your answer to 2 decimal places.
3
Oil (SG=0.82)entering a pump throughan 180mm diameter pipeat 35kPa has a flow rate of0.07 m3/s. It leaves thepump through a 120mmdiameter pipe at 120 kPa.a. Assuming that the suction and dischargesides of the pump are at the sameelevation, determine the energy addedbetween the two points due to the pump.b. Find the horsepower delivered to thewater by the pump (746 watts = 1 HP).
Give the solution.
An 8 hp pump is installed near the reservoir container of oil having a s.g. Of 0.82. The rate of flow of the pipe is 0.014 ?3/s. The pressure at 1 and 2 are -28 kPa and 290 kPa respectively. a. Compute the head added by the pump in meters.b. Compute the output hp of the pump.c. Compute the efficiency of the pump
A pump draws water at 20 liters per second from reservoir A and lifts it to reservoir B, as shown in Figure FM-P-113. The head loss from A to 1 is three times the velocity head in the 150-mm diameter pipe, and the head loss from 2 to B is fifteen times the velocity head in the 100-mm diameter pipe. Choices are in the images Determine: Power delivered by the pump in kW Pressure head at point 1 in m. Pressure head at point 2 inm.
Water is pumped from a supply reservoir to a ductile iron water transmission line. The high point of the transmission line is at point A 1 km downstream of the supply reservoir and the low point of the transmission is at point B 1 km downstream of point A. If the flow rate through the pipeline is 1m³/s the diameter of the pipe is 750mm and the pressure at A is to be 350 kPa. A) estimate the head that must be added by the pump. B) estimate the power supplied by the pump. C) calculate the water pressure at B.
A pump draws water from reservoir A and lifts it to reservoir B as shown in Figure below. The loss of head from A to 1 is equal to the velocity head in the 150-mm pipe and the loss of head from 2 to B is 15 times the velocity head in the 100-mm pipe. Determine the horsepower output of the pump and the pressure heads at 1and 2 when the velocity of flowing water at the 150 mm diameter pipe is 1.5 m/s.
Calculate the mechanical power [hp] required on the pump shaft considering the hydraulic system Shown. The pipe is made of commercial steel (roughness = 0.0002 ft) and has two different diameters, up to the pump inlet the pipe is 2 inches with a length of 100ft and from the pump outlet the pipe is 4 inches with 400ft. All elements are screwed The flow rate circulating through the system is 0.5 ft3/s and the efficiency of the pump is 85%. The density of water is 1.94 slug/ft3 and has a viscosity kinematics 1.1x10-5 ft2/s
Oil with a sp.gr. of 0.86 is being pumped from a reservoir shown. The pressures at the points 1 and 2 are 4 psi and 43 psi respectively. The rate of flow in the pipe is 0.50 ft³ /s. The pump is rated at 8 hp, calculate; The head added by the pump. a. b. The output horse power (hp) of the pump. The efficiency of the pump. C. Pa=43 ps 2"Ø pipe R=4psi "$ tipe oil