In intravenous feeding, a needle is inserted in a vein inthe patient’s arm and a tube leads from the needle to a reservoir of fluid1density 1050 kg/m32 located at height h above the arm. The top of thereservoir is open to the air. If the gauge pressure inside the vein is 5980 Pa,what is the minimum value of h that allows fluid to enter the vein?Assume the needle diameter is large enough that you can ignore theviscosity of the fluid.

In intravenous feeding, a needle is inserted in a vein inthe patient’s arm and a tube leads from the needle to a reservoir of fluid1density 1050 kg/m32 located at height h above the arm. The top of thereservoir is open to the air. If the gauge pressure inside the vein is 5980 Pa,what is the minimum value of h that allows fluid to enter the vein?Assume the needle diameter is large enough that you can ignore theviscosity of the fluid.

Similar questions

B. An ideal incompressible fluid flows at 0.4 m/s throug a square pipe with a side of 7.0 cm. The pipe narrowst a cylindrical pipe with a radius of 30 mm. assume steac flow throughout the system. What is the speed of fluid through the narrow section of the pipe?
An ideal incompressible fluid flows through a pipe of diameter 5.9 cm at a speed of 4.0 m/s. What volume of water passes any single location in the pipe over 3.9 s? Give your answer in m³.
Find the pressure difference required between the ends of a 2.00 m long, 1.00 mm diameter horizontal tube for 40° C water to flow through it at an average speed of 4.0 m/s. Water at 40° has a viscosity of 0.7 x 10-3 Pa s. The pressure difference is equal to ______x105 Pa. Recall the equation for volume flow rate with viscosity: Δ?Δ?=??4Δ?8??
The drawing shows an intravenous feeding. With the distance shown, nutrient solution (p = 1040 kg/m³) can just barely enter the blood in the vein. What is the gauge pressure of the venous blood? Express your answer in millimeters of mercury. Number i Units Atmospheric pressure > en 0.610 m
Suppose you have a 8.8 cm diameter fire hose with a 3.6 cm diameter nozzle. a) Calculate the pressure drop due to the Bernoulli effect as water enters the nozzle from the hose at the rate of 40.0 L/s. Take 1.00 × 103 kg/m3 for the density of the water. b) To what maximum height, in meters, above the nozzle can this water rise? (The actual height will be significantly smaller due to air resistance.
A typical blood pressure is 120 mm Hg. How high above the injection site would you need to hang an IV bag so that the fluid enters the blood stream at this pressure? Assume the IV fluid has a density of 1000 kg/m3. Remember, 1 mm Hg = 133 Pa
While taking a shower, you notice that the shower head is made up of 36 small round openings, each with a radius of 2.00 mm. You also determine that it takes 2.00 s for the shower to completely fi a 1.00-liter container you hold in the water stream. The water for the shower is pumped by a pump that is 5.60 m below the level of the shower head. The pump maintains an absolute pressure of 1.50 atm. Use g = 10 m/s?, and assume that 1 atmosphere is 1.0 x 105 Pa. (a) At what speed does the water emerge from the shower head? 1.105 m/s (b) What is the speed of the water in the pipe connected to the pump? m/s (c) What is the cross-sectional area of the pipe connected to the pump? m2
A liquid-filled tube called a manometer can be used to measure the pressure inside a container by comparing it to the atmospheric pressure and measuring the height of the liquid. Such a device (filled with water) is shown in the figure, measuring the pressure inside a balloon filled with an unknown gas. The water level on the side of the manometer which is open to the air is 12.2 cm higher than on the side connected to the balloon. a. Find the gauge pressure in the balloon, in units of Pa. Recall the density of water is 1000 kg/m3. b. Find the absolute pressure in the balloon, in units of Pa.