) In figure below, the pressure p2 = 30,4 KN/m², whereas the velocity of the water is v₂ = 2 m/s. The diameter of the pipe at location 1 is 100 mm and it is 500 cm above the ground. If the diameter of the pipe at location 2 is 4 cm, and the pipe is 2 m above the ground, find the velocity of the water v₁ at position 1, and the pressure p₁ of the water at position 1.

) In figure below, the pressure p2 = 30,4 KN/m², whereas the velocity of the water is v₂ = 2 m/s. The diameter of the pipe at location 1 is 100 mm and it is 500 cm above the ground. If the diameter of the pipe at location 2 is 4 cm, and the pipe is 2 m above the ground, find the velocity of the water v₁ at position 1, and the pressure p₁ of the water at position 1.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The oil flows through the vertical venturi tube as shown in the figure. The venturi inlet has a diameter of 20 cm, the isthmus of the venturi is 10 cm in diameter, the pressure at inlet P1 is 41.4 kPa(gage), and the pressure at the isthmus P2 is the same size as the body of water. The same oil which is 1.52 m. Find the flow rate of this oil. The density of the oil is 849 kg/m3.
the open tank in the figure contains water and is being filled through section 1. Assume incompressible flow. If the water level h is constant, determine the exit velocity V2 for the given data V1 = 3 m/s and Q3 = 0.01 m3/s.
1. A sphere of radius a is moving with velocity U along the axis of a tube with circular cross-section of radius a(1 + €) with a closed end. See Figure 1. Determine the force exerted by the fluid on the sphere if the Reynolds number and e are small.
Study the motion of the fluid has the complex potential in the form : W = - m In Z where m is a real positive constant .
Fluid Mechanics
what will be the pressure gradient (kpa/m) at L=30 cm through the nozzle? At L=0, the liquid flows inside the nozzle has a specific gravity S=4.4, at L=0, the velocity is 2 m/s while at L=70 cm, the velocity is 6 m/s. Assume steady and inviscid flow. The velocity varies linearly with distance through the nozzle. 70 cm 6 m/s 2 m/s 60 cm Liquid
Water flows through pipe A whose diameter is 30 cm and into parallel pipes 1, 2 and 3 and out through Pipe B (diameter= 30 cm). The properties of the pipe are as follows: for pipe 1, L= 300 m, diameter = 10 cm f= 0.020; for pipe 2 L= 240 m diameter= 15 cm f= 0.018 and for pipe 3, L= 600 deiameter= 20 cm f= 0.017. The upstram junction has an Elev. 90 m with pressure of 205 kPa; the downstream junction is at Elev. 30 m. If the average velocity in pipe A is 3.0 m/s, find the flow rate in pipe 3. Provide FBD and choose the right answer below a.24.68 L/s b.212.0 L/s c.80.21 L/s d.107.11 L/s Clear my choice
Problem Consider a cylindrical pipe of length L and diameter D = 2R. The angle that the axis of the pipe forms with the vertical direction is a. Assume that when the fluid enters the pipe its velocity is uniform (i.e., it has the same value over the entire cross-section of the pipe) and equal to U in the axial direction. In the radial and angular directions, the velocity is zero. So, it is: 2 =0: v(r, 0, 2) = Ue, (1.1) Here v is the fluid velocity and e, is a vector of unit magnitude parallel to the coordinate axis z; furthermore, we have assumed that the pipe inlet is located at z = 0. Near the entrance of the pipe, the velocity profile varies in the axial direction. But after a certain entrance length, the profile becomes fully developed, no longer changing with z. The evolution of the velocity profile is sketched in Fig. 1, where, for clarity, the pipe inclination is not shown. The entrance length is denoted by L.. For z > L., the fluid velocity is no longer a function of the axial…
A horizontal fan (such as that shown in example 5.24) pulls in stagnant air (ie. basically stationary air) atatmospheric pressure; the air approaches the fan outlet with speed 44 ft/sec (ie. 30 mph) and with static pressure 0.3 psi. The air flowing through the fan can be assumed to have a constant density of 2.4*10-3 slug/ft3. The air losses due to friction are 0.1 psi (or 6000 ft-lb/slug of air passing from the fan inlet to the outlet). a) Determine the shaft work in ft-lb/slug b) If the fan outlet area is 2 ft2, determine the rate of work on the air.
help
For the flow of an incompressible fluid, the velocity in x-direction u ax by and velocity in z direction is zero. Find volocity component in y-direction such that v = 0 at y = 0.
The power 491 W is required to transmit 3 x 103 m/s of water. Find the loss of head due to friction in a pipe. The head loss due to friction (in m of water)