In figure (5), if the 50 kg loadA is hoisted by motor M so that the load has a constant velocity of 1.5 m/s. 6) What is the power input to the motor, which operates at an efficiency 60 % or (0.6)? a) 589.2 W b) 919.7 W c) 488.3 W d) 125.9 W 1.5 m/s e) 712.4 W f) 817.5 W g) None of them Figure (5)

In figure (5), if the 50 kg loadA is hoisted by motor M so that the load has a constant velocity of 1.5 m/s. 6) What is the power input to the motor, which operates at an efficiency 60 % or (0.6)? a) 589.2 W b) 919.7 W c) 488.3 W d) 125.9 W 1.5 m/s e) 712.4 W f) 817.5 W g) None of them Figure (5)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3B) A metal is fabricated by drawing at 125 °C. The metal melting temperature is 400 °C. Find by calculation whether this foming process is cold or wam or hot working. Ans--
Manufacturing Processes Q1. Chose the correct answer: 1. Which of the following are variations of sheet-metal-bending operations: (a) coining, (b) flanging, (c) hemming, (d) ironing, (e) notching, (f) shear spinning, (g) trimming, and (h) tube bending? 2. Springback in a sheet-metal-bending operation is the result of which one of the following: (a) elastic modulus of the metal, (b) elastic recovery of the metal, (c) overbending, (d) overstraining, or (e) yield strength of the metal? 3. The cutting force in a sheet-metal blanking operation depends on which mechanical property of the metal (one correct answer): (a) compressive strength, (b) modulus of elasticity, (c) shear strength, (d) strain rate, (e) tensile strength, or (f) yield strength? 4. A circular sheet-metal slug produced in a hole punching operation will have the same diameter as (a) the die opening or (b) the punch? 5. As sheet-metal stock hardness increases in a blanking operation, the clearance between punch and die should…
Q.B3. As part of a project, students have been asked to cast an Aluminium disc for use as a flywheel. The flywheel is part of an engine development project and needs to be 200 mm in diameter and 20 mm thick. Green sand casting will be used. The shrinkage associated with this metal and process is 5% at the solidification stage and further 3 % on cooling to room temperature. Aluminum has a density of 2710 kg/m³ and a melting temperature of 660°C. The pouring temperature is 700°C while the specific heat of aluminum is 887 J/kg.K. The latent heat of fusion of Aluminum is 396 kJ/kg. From previous experiments the Chorinov constant for the mold was found to be 10 s/mm². Determine: a.) The dimensions of the pattern (diameter and thickness) that will need to be made for this part (ignore riser and sprue). b.) The time it will take for complete solidification of the part. c.) Assuming an electric furnace at 10% efficiency is used to heat the metal and it takes around 2 hours achieve pouring…
Question 2: Calculate the required percentage form the following scrap, which would satisfy the following composition for the production of casting billet-MS 70 (70% Cu- 30% Zn) %Cu -90 58 Charge Red brass scrap MS 58 %Zn 10 42
Increasing the degree of graphite nodularity produces an improvement in cast iron elongation, due to ........... .........
Q1) One way of shaping raw materials into useful and valuable products is through casting process. Casting technology or process is one of the oldest processes in manufacturing field. During the last century, this casting process is used to create gold, jewellery and other products. (i) Draw TWO (2) casting processes that would be most suitable for making a gold and jewellery. (ii) Discuss your answer in (i) (iii) Explain why sand-casting process is not suitable for making a gold and jewellery.
Give an example of Dilatation?
Please answer the MCQ's in the image