In experiment 8, the induced emf on the second solenoid is measured by a multimeter. What is the average and maximum voltage on the second solenoid? VQ +F 400MA 10 A 600V fused- METRA max 12 600V CATI IEC61010-1 300V CATII V V. 0.045 AUTO MIN/MAX HOLD/ON AUTO /MAN 1) + OFF Hz mA- V~ 7\ 400KQ 400kQ Hz mA FREL 772 OFF

Q: 6 A R₁ L₁ m L2 R₂3 in L3 ell R3 i2

A:

Q: A V = 47.0 V power supply fully charges a capacitor with capacitance C = 1.37 µF. The capacitor is…

A: The LC circuit described above performs oscillations, where at a time, the total energy in the…

Q: In an oscillating LC circuit, L = 1.24 mH and C = 4.80 µF. The maximum charge on the capacitor is…

A:

Q: 7-turn solenoid has a radius of 7.25 mm and an overall length of 15.0 cm. (a) What is its…

A:

Q: the battery long after the switch has been closed A 1,8 MF Capacitor is charges to 55 V by abort…

A:

Q: A 20.5 Hz, 17.5 V source produces a 1.8 mA current when connected to a capacitor. What is the…

A: f = 20.5 HzV = 17.5 VI = 1.8 mA and C = ?

Q: A * O 11% 0 4:50 PM Domestic power source has rms voltage 120 V and a frequency of 60 Hz. When you…

A:

Q: In circuit below, a long time after the switch is closed (i.e. battery is connected in the circuit),…

A: Step 1: Step 2: Step 3: Step 4:

Q: Tarik winds a small paper tube uniformly with 191 turns of thin wire to form a solenoid. The tube's…

A:

Q: In the L-C circuit in the figure, the ammeter reads a maximum cur­rent of I = 5.19 mA. The…

A:

Q: What rms current flows in a 60-mH inductor when 120-V rms ac at a requency of 20 kHz is applied to…

A: Given:-  The inductor L = 60 mH  The RMS value of the voltage is vrms = 120 V  The frequency that is…

Q: answer ASAP! The RL circuit shown is driven by an EMF source E(t) = E0coswt with E0 = 400 V L = 0.1…

A: This problem can be solved using the the expression for resistance of inductor and some LR circuit…

Q: A 524-turn solenoid has a radius of 8.65 mm and an overall length of 13.8 cm. (a) What is its…

A:

Q: = 200 Ω, C = 70.0 μF, L = 230 mH, fd = 60.0 Hz, and ℰm = 36.0 V. What are (a) Z, (b) ϕ, and (c) I…

A:

Q: In experiment 8, the induced emf on the second solenoid is measured by a multimeter. What is the…

A: Given : Induced emf as measured by a multimeter = 0.045 V

Q: An RLC circuit is used in a radio to tune into an FM station broadcasting at f = 99.7 MHz. The…

A:

Voltage Across Inductor

An actor is a passive electrical component that consists of a coil bent in the form of wire which uses electromagnetism to produce electric current through the coil. When the electric current flows through a conductor that is the coil, a magnetic flux is developed around the conductor. This flow of current through the coil creates a magnetic field based on Fleming's Right-hand thumb rule. If there is any decrease in the current passing through the inductor, then the magnetic field will also decrease and energy is released through the generation of electric current. There is also a secondary voltage inducing in the same coil due to the magnetic flux, since it opposes any changes in the electric current flowing through the circuit. An inductor is also called choke, coil, or solenoid. A choke is designed to block certain frequencies when the DC current passes. A winding coil is coated with insulation to give extra insulation and protect the circuit. They are usually tightly wrapped around a central core which is cylindrical in nature so that the magnetic flux can be induced. The solenoid is a three-dimension coil that is used to exhibit electromagnetism when the magnetic field is developed due to the current flowing through the coil. The sign convention of the inductor is the same as the power dissipating device. When the current flows into the positive side of the voltage across the inductor, the value is positive and the inductor dissipates power whereas when the inductor releases the power back to the circuit, the current has a negative sign convention.