In earlier times when many households received nondigital television signals from an antenna, the lead-in wires from the antenna were often constructed in the form of two paral- lel wires (Fig. P31.50). The two wires carry currents of equal magnitude in opposite directions. The center-to-center separation of the wires is w, and a is their radius. Assume w is large enough compared with a that the wires carry the current uniformly distributed over their surfaces and negli- gible magnetic field exists inside the wires. (a) Why does this configuration of conductors have an inductance? (b) What TV antenna TV set Figure P31.50 constitutes the flux loop for this configuration? (c) Show that the inductance of a length x of this type of lead-in is w - a L In a

In earlier times when many households received nondigital television signals from an antenna, the lead-in wires from the antenna were often constructed in the form of two paral- lel wires (Fig. P31.50). The two wires carry currents of equal magnitude in opposite directions. The center-to-center separation of the wires is w, and a is their radius. Assume w is large enough compared with a that the wires carry the current uniformly distributed over their surfaces and negli- gible magnetic field exists inside the wires. (a) Why does this configuration of conductors have an inductance? (b) What TV antenna TV set Figure P31.50 constitutes the flux loop for this configuration? (c) Show that the inductance of a length x of this type of lead-in is w - a L In a

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A silver wire has resistivity p = 1.60 × 108 Q-m and a cross-sectional area of 2.20 mm2. The current in the wire is uniform and changing at the rate of 2850 A/s when the current is 180 A. (a) What is the magnitude of the (uniform) electric field in the wire when the current in the wire is 180 A? (b) What is the displacement current in the wire at that time? (c) What is the ratio of the magnitude of the magnetic field due to the displacement current to that due to the current at a distance r from the wire? (a) Number i Units (b) Number i Units (c) Number i Units
The figure below is a cross-sectional view of a coaxial cable. The center conductor is surrounded by a rubber layer, an outer conductor, and another rubber layer. In a particular application, the current in the inner conductor is I, - 1.20 A out of the page and the current in the outer conductor is I, = 3.16 A into the page. Assuming the distance d = 1.00 mm, answer the following. (a) Determine the magnitude and direction of the magnetic field at point a. magnitude 240 direction upward (b) Determine the magnitude and direction of the magnetic field at point b. magnitude direction -Seloct
The figure below is a cross-sectional view of a coaxial cable. The center conductor is surrounded by a rubber layer, an outer conductor, and another rubber layer. In a particular application, the current in the inner conductor is I1 = 1.20 A out of the page and the current in the outer conductor is I2 = 2.86 A into the page. Assuming the distance d = 1.00 mm, answer the following. (a) Determine the magnitude and direction of the magnetic field at point a. magnitude µT direction (b) Determine the magnitude and direction of the magnetic field at point b. magnitude µT direction
B6
The beam, consisting of electrons with constant kinetic energy and uniform density, carries a current of 1 mA.The beam has a cross-sectional area of 23 mm^2, electron density 3x10^12 cm^-3. If the electric current is to the rightIf it is oriented, what is the magnitude (m/s) and direction of the velocity of the electrons? A) 61, leftB) 71, rightC) 51, rightD) 91, leftE) 57, left
A copper wire with a square cross-section (side length 5.00 µm) is next to an iron wire with a rightward current of 3.00 A. The two wires are parallel over a region of 20.0 cm, where they are 1.60 cm apart. The iron wire produces a magnetic field on the copper wire. The copper wire is connected to a 5.00 V power source, with current directed rightward. Data of copper: resistivity = 1.68 x 10-8 Ohm m; free electron number density = 8.50 x 1028/m3
Draw a sketch of the situation in the figure, showing the direction of electrons carrying the current, and use RHR-1 to verify the direction of the force on the wire.
The figure shows a cross section of a long, conducting coaxial cable of radii a, b and c. Uniform current density flows through the two conductors such that the total current through the inner conductor is I and total current through the outer conductor is I. Derive the expression for B(r) in the regions ra and sketch a plot of B(r).
The two wires shown in the figure below are separated by d = 10.4 cm and carry currents of I = 5.40 A in opposite directions. Two vertical, parallel wires are separated by a distance d. To the left of the left wire is an arrow labeled I pointing up. To the right of the right wire is an arrow labeled I pointing down. A point P2 is a distance 2d to the left of the left wire, and a point P1 is a distance d to the right of the right wire. (a) Find the magnitude and direction of the net magnetic field at a point midway between the wires. magnitude ?T direction (b) Find the magnitude and direction of the net magnetic field at point P1, 10.4 cm to the right of the wire on the right. magnitude ?T direction (c) Find the magnitude and direction of the net magnetic field at point P2, 2d = 20.8 cm to the left of the wire on the left. magnitude ?T direction
Figure CQ19.7 shows a coaxial cable carrying current I in itsinner conductor and a return current of the same magnitudein the opposite direction in the outer conductor. Themagnetic field strength at r = r0 is B0. Find the ratio B /B0 at(a) r = 2r0 and (b) r = 4r0.
Problem 7: A solenoid is created by wrapping a L = 35 m long wire around a hollow tube of diameter D = 4.5 cm. The wire diameter is d = 0.75 mm. The solenoid wire is then connected to a power supply so that a current of I = 4.5 A flows through the wire. Randomized Variables L= 35 m D= 4.5 cm d = 0.75 mm I= 4.5 A Part (a) Write an expression for the number of turns, N, in the solenoid. You do not need to take into account the diameter of the wire in this calculation. N = | 7 8 9. JT НOME d 1^ AL 4 5 6. a h 1 2 3 j k + END - m P VO BАСKSРАСE CLEAR DEL Submit Hint Feedback I give up! Part (b) Calculate the number of turns, N, in the solenoid. Part (c) Write an expression for the length of the solenoid (L2) in terms of the diameter of the hollow tube D, the length of the wire L and the diameter of the wire d. Assume it is constructed by using only 1 layer of loops (note that most solenoids are actually constructed with many layers, to maximize the magnetic field density). Part (d)…