Question 3In combinatorial logic circuits, outputs are only dependent onThe clock signalb. The history of the inputsThe inputs and previous outputsThe inputsd.

In combinational logic circuits, NAND, NOR or NOT gates are used to produce more sophisticated…

Answered: In combinatorial logic circuits,…

In combinatorial logic circuits, outputs are only dependent on a The clock signal Ob The history of the inputs c The inputs and previous outputs Od The inputs

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

This area has examples of every computer configuration ever used, as well as those that will be used in the future.
1. Given the following circuit: 5 ns D. 1ons The gate delays are as shown above the gates. A, B, C are three input, and all of them are varying, as given below: A = 0 at time 0, and stays constant until time = 20 ns, when it changes to 1 and stays constant there after B = 1 at time = 0, and stays at 1 value until time = 35 ns, and then changes to 0 at35 ns, and stays constant after that. !3! %3D C= 0 at time 0 and changes to 1 at 50ns Plot A, B, C upto time = 70 ns.
la. Draw the truth table for the following set of gates with inputs A, B, C and D and result R: NOT - A OR AND - B R OR NOT -C - -D - b. Use the truth table to generate a Booleanexpression describing the function (using minterms))
A 1bit 4 to 1 multiplexer, the 4 inputs of the multiplexer will be the output of another combinational circuit with A and B as an input:00 = 1bit Adder01 = 1bit Subtractor10 = 1bit Comparator (equals)11 = XOR • truth table• Boolean Expression• Logic Circuit Here is the truth table guide:
Write the logic expression for the output (Q) in the following circuit. A B
4. Design a combinational circuit with three inputs x, y, z and three outputs A, B, C. The output is equal to 0 when the input variable has more 1's than 0's and the output is equal to 1 more than the binary input whose input variables have more 0's than 1's. Fill the values in the truth table and draw the logic diagram (few values are filled for reference) X 0 0 0 0 1 1 1 1 y 0 0 1 1 0 0 1 1 Z 0 1 0 1 0 1 0 1 DB = A'x DA = (AX+BX) A 0 0 B 0 0 5. Design a sequential circuit with two D flip-flops A and B, input x and output Y. The flip-flop input equations and the circuit output equations are as follows: C 1 Y = (A+B)x (Draw the circuit diagram and state table) 0
Computer Science Design combinational logic for outputting the wait time associated with each state. For example, state 000 has the main street green light on for 15 seconds. The combinational logic for the input 000 would have an output 1111 corresponding to decimal 15. Let the outputs W3, W2, W1 and W0 represent a binary number corresponding to the wait time.
Show a Logic Circuit Diagram for the following Boolean Expression: F = abc + a'c'
A Full Adder Circuit is shown in Figure 1 utilizing two Half Adders and an OR Gate. The major input bits are A and B, the carry input is CIN, and the Sum and Carry Outputs are COUT, respectively. simulate it using C programming Efficient logic, use of loops and conditional statements Truth table: (Half adder) A B Sum Pi=A⊕B Carry, Gi=AB 0 0 0 0 0 1 1 0 1 0 1 0 1 1 0 1 Truth table: (Full adder) A B Ci Sum, S=A⊕B⊕Ci Carry, C0=AB+CiA⊕B 0 0 0 0 0 0 0 1 1 0 0 1 0 1 0 0 1 1 0 1 1 0 0 1 0 1 0 1 0 1 1 1 0 0 1 1 1 1 1 1
Design a sequential circuit (overlapping) with an input ‘x’. The pattern to be detected is the binary number that is equal to 01100 For example,the circuit detects the sequence 00010 . When the sequence is detected, the detector outputs z=‘1’ For this circuit:Draw the logic circuit for the datapath
= 1 causes the heater to decrease its Q3: A Moore sequential circuit has three inputs (X2, X1, and Xo) that specify a temperature range in a room. The circuit has two outputs (I and D) that control a heater for the room; I = 1 causes the heater to increase its heat output, and D heat output. If the temperature range is 0, 1, or 2 for three successive clock cycles, the circuit generates I = 1, and conversely if the temperature range is 5, 6, or 7 for three successive clock cycles, the circuit generates D = 1; otherwise, I = 0 and D = 0. 1. Draw a state diagram. 2. Construct a state table. 3. Using D flip-flops, construct a state assigned table. 4. Determine the next-state and output logic expressions. 5. Sketch the corresponding logic circuit.
In a sequential logic circuit, the next output is dependent on the previous output and the inputs. O a. Ob The only input is the clock signal. The background of the OC inputs. The sole data source is Od.