Answered: In CE configuration, if the voltage…

In CE configuration, if the voltage drop across 5kΩ resistor connected in the collector circuit is 5V. Find the value of IB when β=50. A) 0.25mA B) 0.01mA C) 0.02mA D) 0.03mA

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter12: Batteries And Other Sources Of Electricity

Section: Chapter Questions

Problem 3PA: An office building uses a bank of 63 lead-acid cells connected in series with a capacity of 80...

See similar textbooks

Related questions

Q: Which of the following statements are FALSE?

Q: Sketch i0 and v01 for the network below for the input shown (Both diodes are Si. Vd = 0.7 V)…

A: During the positive half cycle only diode D1 is forward biased and it will conduct and with the help…

Q: The term bias means the ratio of majority carriers to minority carriers a dc voltage is applied to…

Q: Find I and V using the constant voltage drop model to model the diodes (Hint: assume both diodes are…

Q: Determine the aspect ratio of the NMOS in the circuit to produce a drain current of 150 uA. R2 2.5k…

A: Brief description : Generally mosfets are known as high input impedance devices. MOSFET's have four…

Q: For the circuit shown, what is the voltage Up across the Zener diode with a breakdown voltage vz 10…

Q: Determine VL, IL, IZ and IR

A: APPLY KVL to input loop 25-IR.RS –Vz =0 IR =25-6.2/270 =0.06963 IR=69.63 Iz max =Pz.max…

Q: Analyze the following circuit and calculate the final current that passes through the diodes R1 D1…

Q: A 4-layer diode turns on when the anode-to-cathode voltage exceeds 0.7 V O The gate voltage the…

A: Here is the explanation

Q: •Vss =5 V and R=0.5 km ,For the shown circuit Vss 文 vp :The diode current is A 1.5 mA 8,5 mA 20

A: Fig: Given circuit In the given circuit diode is forward bias Assume that voltage drop…

Q: Find the Q point value of the diode current and the voltage gain Av in the following circuit: 700Ω…

A: Diode It is an unidirectional electrical device, which allows current to flow only in one specific…

Concept explainers

Photoconductive Cell

Photoconductive cells are light-sensitive resistors in which resistance is inversely proportionated to light intensity when illuminated. These devices consist of a thin single-crystal or polycrystalline film of composite semiconductor materials. Cadmium sulfide (CdS) is used to make the most commercially available photoconductive particles which are sensitive to light in the visible spectrum. Other less commonly used substances respond to infrared light, but not to the visible spectrum. Such substances are lead sulfide (PbS), lead selenide (PbSe), and lead telluride (PbTe), and so on.

Question

In CE configuration, if the voltage drop across 5kΩ resistor connected in the collector circuit is 5V. Find the value of I_B when β=50.

A) 0.25mA

B) 0.01mA

C) 0.02mA

D) 0.03mA

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Determine the base current:

VIEW

Step 2: Find collector current :

VIEW

Step 3: Find base current:

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Design a bias circuit for NPN silicon transistor having a nominal B-100 to be used in voltage divider circuit with Q-point of Ic 10 mA and VCE= 10 V. Use standard valued 5% resistors and draw a schematic %3D diagram of your design
Please answer all parts of the question with step by step working and explanantions so i understand the questions and solution better thank you.
Question in the photo attached please
A silicon solar cell has a short circuit current of 90 mA and an open-circuit voltage of 0.75v under solar illumination. The fill factor is 0.8. What is maximum power delivered to a load by this cell?
A base current of 50 μA is applied to the transistor in Figure below, and a voltage of 5V is dropped across RC. Determine the B of the transistor Van Ra 100 k Rc1.0kn th M Voc
not use ai please don't
The circuit shown below is to be used to provide a stabilised output to the load. The Zener diode characteristic is also shown on the next page. Find the load voltage (VL) and source current (IS) if the battery voltage is 18 V, series resistance is 1.4 KΩ and load resistance is 11 KΩ. Additionally, determine the value of the source resistance (R) if the Zener diode is at the threshold of activating in its reverse bias. Comment on the purpose of having this value of R in the circuit.
The term "Bipolar" in Bipolar Junction Transistor (BJT) refers to 5 Ja) Two junctions c) Two polarity carriers (electrons & holes) b) Two Diodes d) Two resistances negative of dinda b' nositivo
Sketch i0 and v01 for the network below for the input shown (Both diodes are Si. Vd = 0.7 V) Explain your drawings, briefly pls.
If the current across the diode here in the figure is 0, does that mean the voltage across the resistance (10 ohms) is 0 because of V=IR or it is 5V?
A silicon diode with a forward resistance of 10Ω is connected in series with a 500Ω resistor. If an A.Cvoltage of 20V peak is connected across the series combination of the diode and the resistor what willbe the peak value of the current through the diode and the peak output voltage? What will be the peakvalue of the current through the diode and the peak output voltage if the diode were ideal?
a) To what value R must be adjusted in the following circuit to make IZ = 70 mA. Assume VZ =20 V at 65 mA and ZZ = 23 Ω. What is the Zener voltage at 70o C, if it has a positive TC of 0.08 %/oC.? b) Using a Complete diode model, find the diode current (ID), diode voltage (VD), and output voltage (Vo) for the diode circuit shown below. Given that: Vs = 20 V, RL=3 kΩ , Barrier Potential VF = 0.3 V , and r’d = 70 Ω. If the diode was reversed and IR = 200 µA, Determine the diode reverse voltage (VR)