In audio and communications systems, the gain, B, in deci- bels is defined for an amplifier as Pout B = 10log Pin where Pin is the power input to the system and Pout is the power output. (a) A particular amplifier puts out 135 W of power for an input of 1.0 mW. What is its gain in dB? (b) If a signal-to-noise ratio of 93 dB is specified, what is the noise power if the output signal is 10 W?

In audio and communications systems, the gain, B, in deci- bels is defined for an amplifier as Pout B = 10log Pin where Pin is the power input to the system and Pout is the power output. (a) A particular amplifier puts out 135 W of power for an input of 1.0 mW. What is its gain in dB? (b) If a signal-to-noise ratio of 93 dB is specified, what is the noise power if the output signal is 10 W?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A pipeline of length 20 km is used for transmission of water. If the 100 kW power is to be transmitted through the pipe in which water is having 981 N/cm2 pressure at inlet of the pipe, find the diameter of the pipe corresponding to maximum efficiency of transmission, where f = 0.026.
For the amplifier shown in Figure 1, the BJT parameters are ß = 75, Vag (on) = 0.7 V, VCE (sat) = 0.3 V, VA = 100, and V, 25 mv. Voe=9V R= 27 ka 22 ka Rs = 10 ka Ca ER= 2 k2 R= 15 k2 12 kQ The value of the DC base current Ig is
Write the function of (i) Transducer and (ii) Repeater in the context of communication system.
Problem 4: Two wattmeters are connected to measure the input power of a balanced 3-phase load by the two-wattmeter method. If the wattmeter readings are 8 kW and 4 kW, find (a) total power input, and (b) load power factor
Show that when the gain of summing amplifier is unity, the output voltage is the algebraic sum of the input voltages with proper circuit diagram.
Q2. a) Using the concept of feedback, explain the working principle of an Oscillator b) When negative voltage feedback is applied to an amplifier of gain 200, the overall gain falls to 1000. (i) Calculate the fraction of the output voltage fedback. (ii) If this fraction is maintained, calculate the value of the amplifier gain required if the overall stage gain is to be 102.
Please
The circuit shows the Common Collector Amplifier. a) Find the value of Rout and Rin(emitter) (Bac = 175)? b) Calculate the voltage gain (A,) and current gain (A;)? Vcc +5.5 V R1 10 kΩ) Vin o C2 Vout RE 1 k2 R2 RL 4.7 ka 2 ka
Q1: Find the length of A: Input power = -5 dBm Loss =10 dB gain = 4 dB Output power = -26 dBm Link A 2 km of fiber
A lossless dipole antenna, with input impedance of 73 ohms, is connected to a transmission line whose characteristic impedance is 50 ohms. The radial component of the radiated power density is given by: U, = A,(1/ [csc] 2e – 1) %3D Where A is the peak value of the power density, 0 is the usual spherical coordinate. Determine P D rad' o' G and G (dB). oabs
Suppose we need to develop a new CPU that has 66% of the capacitive loadand will run at 22% reduced voltage compared to your designed CPU.This will result in 22% shrink in frequency. What will be the impact on dynamicpower?
Q4