In an oscilloscope, a 20 V sinusoidal signal produces a deflection of 2cm corresponding to a certain setting of vertical gain control. If another voltage produces 7.3 cm deflection for the same setting of the vertical gain control, what is the peak-to-peak and rms value of the voltage

In an oscilloscope, a 20 V sinusoidal signal produces a deflection of 2cm corresponding to a certain setting of vertical gain control. If another voltage produces 7.3 cm deflection for the same setting of the vertical gain control, what is the peak-to-peak and rms value of the voltage

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 7RQ: An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a...

See similar textbooks

Similar questions

A double beam oscilloscope displays 2 sine waveforms A and B. The time/cm switch is on 150µs/cm and the volt/cm switch on 5 V/cm. The width of each complete cycle is 8 cm for both the waveforms. The height of waveforms A and B are 5 cm and 4 cm respectively. Determine their a) frequency, b) phase difference, and c) peak and d) r.m.s value of voltages. The difference between the two waveforms is 0.7 cm.
A double beam oscilloscope displays 2sine waveforms A and B. The time/cm switch is on 100us/cm and the volt/cm switch on 2V/cm. The width of each complete cycle is 5cm for both the waveforms. The height of waveforms A and B are 2cm and 2.5cm respectively. Determine their a) frequency, b) phase difference, and c) peak and r.m.s value of voltages. The difference between the two waveforms is 0.5 cm.
A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 2 ms/cm and the volt/cm switch on 4 V/cm. The width of each complete cycle is 5.9 cm for both the waveform. The Peak to Peak height of waveform Gand H are 5.6 cm and 5.9 cm respectively. The difference between the two waveform is 1.1. Determine a) frequency, b) phase difference, C) RMS value of G waveform d) peak value of H waveform a) frequency b) phase difference C) RMS value of G waveform d)peak value of H waveform
A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 50 ms/cm and the volt/cm switch on 6 V/cm. The width of each complete cycle is 5.3 cm for both the waveform. The Peak to Peak height of waveform G and H are 4.6 cm and 5.9 cm respectively. The difference between the two waveforms is 0.7. Determine a) Frequency b) Phase difference c) RMS value of G waveform d) Peak value of H waveform a) frequency
3. A double beam oscilloscope displays 2 sine waveforms A and B. The time/cm switch is on 100us/cm and the volt/cm switch on 2V/cm. The width of each complete cycle is 6 cm for both the waveforms. The height of waveforms A and B are 3 cm and 3.5cm respectively. Determine their a) frequency, b) phase difference, and c) peak and r.m.s value of voltages. The difference between the two waveforms is 0.6 cm.
A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 50 ms/cm and the volt/cm switch on 6 V/cm. The width of each complete cycle is 6.8 cm for both the waveform. The Peak to Peak height of waveform G and H are 4.5 cm and 5.5 cm respectively. The difference between the two waveforms is 0.2. Determine a) Frequency b) Phase difference c) RMS value of G waveform d) Peak value of H waveform
ii) A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 2ms/cm and the volt/cm switch on 4 V/cm. The width of each complete cycle is 7.7 cm for both the waveform. The Peak to Peak height of waveform G and H are 4.6 cm and 6.7 cm respectively. The difference between the two waveforms is 0.2. Determine a) Frequency, b) Phase difference, c) RMS value of G waveform. a) frequency b) phase difference c) RMS value of G waveform
3. A sinusoidal waveform displayed on an oscilloscope is shown in Figure 2. The 'time/cm' switch is on 10 ms and the 'volts/cm' switch is on 5V/cm. Determine for the waveform: a) The frequency of both waveforms b) The peak-to-peak value of waveform Q c) The amplitude of waveform P Figure 2
A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 50 ms/cm and the volt/cm switch on 6 V/cm. The width of each complete cycle is 7.1 cm for both the waveform. The Peak to Peak height of waveform G and H are 5.6 cm and 5.7 cm respectively. The difference between the two waveforms is 1. Determine a) Frequency b) Phase difference c) RMS value of G waveform d) Peak value of H waveform a) frequency b) phase difference c) RMS value of G waveform d) Peak value of H waveform
A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 40 ms/cm and the volt/cm switch on 4 V/cm. The width of each complete cycle is 6.8 cm for both the waveform. The Peak to Peak height of waveform G and H are 5.5 cm and 5.3 cm respectively. The difference between the two waveform is 0.8. Determine a) Frequency, b) Phase difference, c) Peak value value of G waveform. c) RMS value of H waveform.
ii) A double beam oscilloscope displays 2 square waveform G and H. The time / cm switch is on 2ms / cm and the volt / cm switch on 4 V / cm. The width of each complete cycle is 6.2 cm for both the waveform. The Peak to Peak height of waveform G and Hare 4.1 cm and 5.5 cm respectively. The difference between the two waveforms is 0.5. Determine a) Frequency, b) Phase difference, c) RMS value of G waveform
The waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 0.2 ms/cm, and the 'volts/cm' switch is set to 40 V/cm. Determine the (i) amplitude of waveform Q, (ii) peak to peak value of waveform P, (ii) frequency of waveform P and (iv) phase angle difference between P and Q in Degrees. Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. (i) Amplitude of waveform Q = (ii) Peak to peak value of waveform P = (iii) Frequency of waveform P = (iv) Phase angle difference between P and Q in Degrees =