In an ideal Rankine Cycle, steam is generated at 4.1 MPa and 480C, the condenser is at 32C. Determine (a) the ideal pump work, (b) the cycle thermal efficiency, (c) for an engine with the same end states, determine its thermal efficiency, steam rate, and mep, (d) considering the engine only, assume the brake efficiency to be 78% the generator efficiency 92%, the steam flow rate of 163 000 kg/hr, compute the output of the combined unit

In an ideal Rankine Cycle, steam is generated at 4.1 MPa and 480C, the condenser is at 32C. Determine (a) the ideal pump work, (b) the cycle thermal efficiency, (c) for an engine with the same end states, determine its thermal efficiency, steam rate, and mep, (d) considering the engine only, assume the brake efficiency to be 78% the generator efficiency 92%, the steam flow rate of 163 000 kg/hr, compute the output of the combined unit

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An ideal Rankine cycle with double reheat operates the boiler at 12MPa, the reheater at 5 MPa and 2.0 MPa, and the condenser at 0.01 MPa. The temperature at the boiler and reheater outlets are maintained at 400°C. a) Determine the total rate of heat transfer per unit mass in the reheaters, andb) the thermal efficiency of this cycle.
turbine turbine Reheater (4 Copy of Boiler P = P5 = Prchcat (5) Pump Condenser The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4 Inlet steam at 17.5 MPa and 600 C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0 1. At state 1, the specific volume is 0.00101 m-kg Find the specific enthalpy in kJ/kg at state 2 to 3 deciamal places
Reference Book: Introduction to Chemical Engineering Thermodynamics by Smith, Van Ness, etc. 7th or 8th Ed.
A steam power plant operates in a Rankine cycle. Steam enters the high-pressure turbine at 10,000 kPa and 450°C and leaves at 20 kPa. The steam leaves the condenser as a saturated liquid. a.) What is the thermal efficiency? b.) For a practical cycle, what is the efficiency of the power plant if the efficiencies of pump and turbine are 0.8 and 0.70, respectively? The volume at the pump is 1000 cm3/kg. c.) Determine the steam rate and heat-transfer rate if the rating of the practical power plant is 90,000 kW.
A power plant using a Rankine power generation cycle and steam operates at a temperature of 81.25°C in the condenser, a pressure of 5 MPa in the boiler and a maximum boiler temp of 775°C. The cycle operates at steady state with a mass flow rate of 2.5kg/s. Use the steam tables in the appendix of Sandler (p. 917 to 925). a.) Draw out the cycle, calculate the work required for the pump, the work output by the turbine, the heat into the boiler, and the heat out of the condenser. b.) What is the efficiency of this power plant? c.) If the turbine was only 89% efficient but still adiabatic (only generates 89% of the calculated work from part b), what is the overall efficiency of the cycle?
2
yale L 15 A gas power cycle uses air as the working fluid and has two turbine sections as shown in the figare below. The power produced by Turbine I is used to drive the compressor, and Turbine 2 produces output power W. Air enters the compressor with a semperature of 290 K and a mass flow rate of -2 (kgs] (State I); the air exits the compressor at 44SK (State 2). Heat is transferred from a high- temperature thermal reservoir, Ta- 1400 [K), to Heat Exchanger 1 at a rate Q,- The lemperature of the air is raised to 1100 [K] (State 3) as it flows through Heat Exchanger 1. The air enters Turbine I where it is expanded to State 4. The flow then proceeds to Turbine 2 and exits with a temperature of 500 (K] (State 5). Heat is then removed from the air through Heat Exchanger 2 at a rate Q which is rejectod to the low-temperature thermal reservoir, TL-200 (K). (A) Determine the temperature at the inlet to Turbine 2, Te (b) Calculate the power output from Turbine 2, W. (e) Calculate the rate of…
1. In a steam power cycle, steam enters the turbine at 30bar with the following different conditions and leaves at 1bar. Calculate Carnot efficiency, Rankine efficiency, condenser heat flow in kW assuming mass flow rate of steam as 9.5kg/s and steam rate for each case considering the pump work. (ii)Wet with 0.95 dryness (iii) Superheat at 550°C
In an ideal Rankine cycle, steam is generated at 4.1 MPa and 480 deg. C. The condenser is at 32 deg. C. Determine: a. The cycle thermal efficiency b. For the engine with the same end states, the thermal efficiency and steam rate.
Q2 Figure Q2 is a Reversed Carnot Cycle with a food department is kept at -12°C. The total heat gain to the food department is estimated to be 3300kJ/h and the heat rejection in the condenser is 4800KJ/h. Calculate i, the power input to the compressor in kW ii. The Coefficient of performance (COP)R of the Plant. TH = 30 QH =4800 Figure (Q2) R Went QL=3300 TL=-12 C °C
. A domestic refrigerator using R-12 as a working fluid .The condensing and evaporating temperatures are 100 F and 25 F respectively. Heat exchanger is added to sub-cooled the saturated liquid to 70 F. Compute; (i) nvc & nv if m=3% & y=1.25, T₁=60 F & A p=2.1 psia. (ii) work done compressor. (iii) C.O.P. Refrigration
A 211 MW steam power plant is proposed that will operate in a Rankine cycle with a condenser pressure of 0.06 bar and the boiler pressure is 50 bar. The maximum temperature in the boiler is 500°C a)Determine the overall efficiency and work ratio of the cycle.