Answered: In a wire drawing operation, diameter…

In a wire drawing operation, diameter of a steel wire is reduced from 10 mm to 8 mm. The mean flow stress of the material is 400 MPa.The ideal force required for drawing (ignoring friction and redund

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

...). A 450 mm-long sheet with a cross sectional area of 320 mm² is stretched with a force, F, until α = 22°. The material has a true-stress-true-strain curve o = 750 x 106 0.35 (a) Find the total work done, ignoring end effects and bending. (b) What is a max before necking begins? F 300 mm - 150 mm
For a body under three dimensional stress state, describe the procedure for obtaining the absolute maximum shearing stress at a given point.
A hole with a diameter of 18 mm will be drilled in a sheet material with a thickness of 4 mm. Calculate the shear force in kN since Rm=640 MPa for sheet material
A hot rolling mill has rolls of radius = 105mm. It can exert a maximum force =1219625 Newton. The mill has a maximum horsepower = 91 hp. It is desired to reduce a 25 mm thick plate by the maximum possible draft in one pass. The starting plate is 250 mm wide. In the heated condition, the work material has a strength coefficient = 275 MPa and a strain hardening exponent = zero. Determine(a) maximum possible draft(b) associated true strain(c) maximum rotational speed of the rolls for the operation
A sheet metal cutting machine cuts the sheet metal via shear force, V as shown in Fig. 1. The crosssection of sheet metal is rectangular with width, b = 3m and thickness, d = 5mm. The sheet metal ishaving yield strength σy = 220 MPa; Young’s modules, E = 200 GPa and Poisson’s ratio, ν = 0.3.Conduct the following analyses at the state of stress when maximum stress reaches σy and beforeshearing commences. (Need answer Question c) & d) c. Sketch the YIELD LOCI for both cases above. d. As a sheet-metal engineer, which failure criterion in (b) will you use to determine the cuttingshear force? Explain the reason for your answer.
In a sheet metal of 2 mm thickness a hole of 10 mm diameter needs to be punched. The yield strength in tension of the sheet material is 100 MPa and its ultimate shear is 80 MPa. Calculate the force required to punch the hole (in kN).
A 250 mm diameter circle is etched on a 400 mm x 400 mm x 12 mm piece of sheet metal. The elastic modulus is 190 GPa and Poisson's ratio is 0.3 for the material If stresses of 40 MPa and 75 MPa are applied in the x and y directions respectively, calculate the following: a) Change in sheet thickness, i.e. find At. Hint engineering and true strain are equal in the elastic regime. b) Sketch the shape of the circle after deformation on the figure below c) What is the elastic strain energy in the thickness direction only?
What are the fundamental problems in Shear stress?
A hole is to be punched out of a plate having a shearing strength of 50 ksi. The compressive stress in the punch is limited to 63 ksi. (a) Compute the maximum thickness of plate in which a hole 6 cm in diameter can be punched.(b) If the plate is 1 cm thick, determine the diameter of the smallest hole that can be punched.
A cylindrical specimen of brass that has a diameter of 15 mm, a tensile modulus of 100 GPa, and a Poisson's ratio of 0.35 is pulled in tension with a force of 40, 000 N. If the deformation is totally elastic and the original length is 120 mm, what is the final diameter of the specimen in mm?