In a transformer, two coils are wound around a toroidal iron core. Answer True or False.A transformer is heavy because of the copper coils.The purpose of any transformer is to produce higher voltage.e If the primary voltage is constant, the secondary voltage is alternating.a The purpose of any transformer is to produce a lower voltage.e The iron core is built up of thin slices of iron.a If the primary voltage is alternating, the secondary voltage is constant.e If the primary voltage is alternating, the secondary voltage is alternating.Submit Answer Tries 0/12

Transformer: A transformer is an electrical energy transfer device that either steps up or steps…

In a transformer, two coils are wound around a toroidal iron core. Answer True or False. e A transformer is heavy because of the copper coils. The purpose of any transformer is to produce higher voltage. e If the primary voltage is constant, the secondary voltage is alternating. e The purpose of any transformer is to produce a lower voltage. e The iron core is built up of thin slices of iron. a If the primary voltage is alternating, the secondary voltage is constant. e If the primary voltage is alternating, the secondary voltage is alternating. Submit Answer Tries 0/12

In a transformer, two coils are wound around a toroidal iron core. Answer True or False. e A transformer is heavy because of the copper coils. The purpose of any transformer is to produce higher voltage. e If the primary voltage is constant, the secondary voltage is alternating. e The purpose of any transformer is to produce a lower voltage. e The iron core is built up of thin slices of iron. a If the primary voltage is alternating, the secondary voltage is constant. e If the primary voltage is alternating, the secondary voltage is alternating. Submit Answer Tries 0/12

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Blue is the numerical answer, I need a detailed solution.
Quiz2: We wish to connect a 6 kVA, 120/240 V transformer as an autotransformer to a 120 V source to supply 360 V to a load. a) Draw the circuit. b) What is the maximum load kVA that can be supplied? c) At the maximum load, determine ln, fy, and I,- d) What are the possibilities to connect it as a step-down autotransformer and determine the load voltage at cach case?
A voltage transformer in Figure 8 has 1,500 turns of wire on its primary winding and 500 turns of wire for its secondary winding. What will be the turns ratio, a of the transformer. If 240 volts is applied to the primary winding, what will be the resulting secondary voltage. And if a 400 n resistor is connected to the secondary winding, what are the values of current Is and Ip. primary Vp Transformer Core NF Ns Figure 8 secondary Vs
The losses found in a transformer
Q2/ Complete the blank A single-phase transformer is rated at 50 kVA. The transformer has full load copper losses of 450 W and iron losses of 150 W. The transformer efficiency at 1/4 th of the full load and 0.95 power factor is...............................................?
5. Transformer cores are laminated in order to (a) simplify its construction (b) minimise eddy current loss (c) reduce cost (d) reduce hysteresis loss. 6. A transformer having 1000 primary turns is connected to a 250-V a.c. supply. For a secondary voltage of 400 V, the number of secondary turns should be (a) 1600 (b) 250 (c) 400 (d) 1250 7. The primary and secondary induced e.m.fs. E, and E₂ in a two-winding transformer are always (a) equal in magnitude (b) antiphase with each other (c) in-phase with each other (d) determined by load on transformer second- ary. 8. A step-up transformer increases (a) voltage (b) current (c) power (d) frequency. F
The full-load copper losses and iron losses. of a transformer are 6400 W and 5000 W respectively. The copper loss and iron loss at half full-load will be respectively (i) 3200 W and 2500 W (ii) 1600 W and 5000 W (iii) 3200 W and 5200 W (iv) 1600 W and 1250 W
If I build a transformer and I have the following data:Primary voltage = 127VNumber of turns in primary = 100 turnsI want to have 8.89 V in secondaryHow many turns should I have on the secondary of this transformer?
Q7/ Complete the blank The copper loss of a transformer at 4/5 of the full load is 4000 W, full load copper loss will be..........................................?
Due to the increase in load, what change you saw in the transformer’s output power and the efficiency?
3. An ideal transformer with a 500 turns primary and 125 turns secondary windings delivers 400W to a 40 load. The resistance of the primary windings is 16O. Find the primary current and voltage
A transformer has "N1" primary turns, primary winding is connected with 'V1' Volts. if N2 = N1/2, what is the secondary voltage? O a. V2 = V1/2 O b. V2=2V1 c. V2=0 O d. V2=V1