In a thrust bearing the external and the internal diameters of the contacting surfaces are 320 mm and 200 mm respectively. The total axial load is 80 kN and the intensity of pressure is 350 kN/m. The shaft rotates at 400 rpm. Taking the coefficient of friction as 0.06, calculate the power lost in overcoming the friction, Also, find the number of collars required for the bearing

In a thrust bearing the external and the internal diameters of the contacting surfaces are 320 mm and 200 mm respectively. The total axial load is 80 kN and the intensity of pressure is 350 kN/m. The shaft rotates at 400 rpm. Taking the coefficient of friction as 0.06, calculate the power lost in overcoming the friction, Also, find the number of collars required for the bearing

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The roughly position of the automobile jack shown in the figure is a square screw with a single blade at both ends. ABC is controlled by a bolt (right-hand threaded in A, left-handed in C). square of the bolt screw has a pitch of 2.5 mm and an average diameter of 9 mm. between the bolt and the jack limbs The coefficient of static friction is 0.15, taking into account the position and load shown, you can use the jack Find the magnitude of the torque that must be applied to raise it.
The pressure distribution at the pivot bearing's surface of contact changes, as indicated. Determine the torque M necessary to overcome friction if the shaft sustains an axial force P and the coefficient of static friction is.
The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.
I need the answer as soon as possible
Find the value of frition if coefficient of friction is 0.3 and normal force is 200 N
I need the answer as soon as possible
I will rate helpful. Thank you.
A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing four pairs of contact surfaces. The outer diameter of the contact surfaces is 250 mm and the inner diameter is 150 mm. Determine the maximum axial intensity of pressure between the discs for transmitting 18.75 kW at 500 r.p.m. Assume uniform wear and coefficient of friction as 0.3.
You have to build a box lifter, this will be made with a square threaded power screw. The power screw is 3 inches in diameter and 2 threads per inch. To improve the speed of raising and lowering the boxes, it must be with triple thread. The coefficient of friction of the screw and collar is 0.25, the diameter of the collar is 4 inches.Calculate:1. The depth of the thread, the width of the face, the average diameter, the root diameter, the pitch and its feed.
A block brake with a torque of 250 N-m. Its drum rotates at 100 rpm. The length of the block (1) is twice its width (w). Assume, the coefficient of friction P is 0.35. Calculate: (1) the applied load (P) and the hinge-pin reaction (Rx ana Ry) for clockwise rotation of the drum; (2) the applied load and hinge-pin reaction for anticlockwise rotation of the drum; (3) the rate of heat generated during the braking action. (4) The dimensions of the block, if the intensity of pressure between the block and brake drum is 1 MPa. (5) Check whether the brake is self-locking.
You have to build a box lifter, this will be made with a square threaded power screw. The power screw is 3 inches in diameter and 2 threads per inch. To improve the speed of raising and lowering the boxes, it must be with triple thread. The coefficient of friction of the screw and collar is 0.25, the diameter of the collar is 4 inches.Calculate:1. The depth of the thread, the width of the face, the average diameter, the root diameter, the pitch and its feed.2. The torque to increase the load and the efficiency of the screw.3. The speed of the motor (in rpm), if it is directly coupled to the screw and it is desired that the boxes rise at a speed of 30 inches/min.