In a stage of Parson's reaction turbine, the mean diameter of the wheel is 1.05 m and the speed is 3000 r.p.m. The angles of receiving tips are 35° and the discharging tips is 20°. If the steam flow rate is 1 kg/min, draw the velocity diagram for blades and evaluate, (a) Tangential thrust on blades (b) Axial thrust on blades (c) Power developed in the blades and (d) Diagram efficiency.

In a stage of Parson's reaction turbine, the mean diameter of the wheel is 1.05 m and the speed is 3000 r.p.m. The angles of receiving tips are 35° and the discharging tips is 20°. If the steam flow rate is 1 kg/min, draw the velocity diagram for blades and evaluate, (a) Tangential thrust on blades (b) Axial thrust on blades (c) Power developed in the blades and (d) Diagram efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

EHide blocks This course An axial flow Impulse gas turbine stage receives a mass flow rate of 76 lbm/s at a velocity V1. It has a hub and tip radii of 7 in and 12 in respectively. The gas leaves the stator with an angle of a;=45° with the tangential direction. The blade angle at the outlet is Bp2=36.07°. Take pgas=0.085 lbm/ft. a1 V1 Um Bb2 Stator Rotor 2 Ping 6232 ms 08 5 KB Determine the absolute velocity at the inlet in ft/s. Choose... Determine the blade angle at the inlet Bp1 Choose... 741
In a trial run, the De Laval steam turbine at Oman Power Plant rotates at 3000 rpm. The steam is issued from the nozzle at 400 m/s and the nozzle angle is 20o. The blade speed ratio is 0.41and the friction loss in the blade channel is 15%of the kinetic energy corresponding to the relative velocity at the inlet to the blades. As a turbine engineer at that station, how do you determine the (i) power developed by the turbine for a flow rate of 10 kg/s and (ii) suitable inlet and outlet angles for the blades when axial thrust is zero. Also, how would you determine the size of the turbine wheel required? Draw a suitable velocity diagram.
A rection turbine has guide vane angle 30° the runner blades make an angle of 80° relative to the tanget at inlet .the blades width at inlet is 1/4 of the outer diameter .the water does not have any tanget velocity at outlet.the head is 25 m and the rotational speed of the runner is 16.67 rotation per second (rps) the turbine efficiency is 88% determine the runner diameter at the inlet and the power developed by this turbine
4. For Francis turbine with the following specifications: Pdev= 225 MW, H=250 m , nov= 90 % , If the velocity of water at spiral case entering =24 m/s, and the volumetric efficiency is 0.98, thus the diameter of the spiral case entering is: а. 2.3 m. b. 2.8 m. с. 3.1 m. d. 3.6 m. e. None of them.
In a Francis turbine, when 6N force is applied to the disc with a radius of 0.08m, the revolution rate is 2500 rpm, the water flow rate is 8 m3 / h, the inlet pressure is 12 mSS and the outlet pressure is 0 mSS. In this case, calculate. Francis turbine efficiency
ENPY = (+ 3.2 cm. Centrifugal pump rotates at 1500 rpm. Water enters the wings normally and exits by 38 degrees from the radial direction. The volumetric flow rate is given as 0.25 m^3/s. By accepting the yield as 100%; A centrifugal pump impeller has an inlet radius of 15 cm and a blade width of 6.3 cm. Its radius at the exit is 35 cm and its wingspan is (a2 = 38°) (Psu = 998 kg/m³) P1 + as 29 pg P2 + d2 29 pg L V² hg sûrekli= f-52g + zz + hpompa.f + hearbing + hg,toplam Re = p.V. D + z2 1.11 = -1.8 log Re 6.9 ɛ / D hkyerel = KK 29 Wmil = 3.7 hg,toplam= hx,sarekli + hx.yerel Протра H = pg z/1ẠM Nsp = (gH)³/4 ротра giris Wmil,B WmilA WR %3D PR (we PA b) Find the required shaft power for the centrifugal a) Find the manometric head provided by the centrifugal pump. pump. 28092 W 17,05 m O 42087 W 21,28 m O 38085 W 13,67 m O 45765 W 12,23 m O 35063 W 15,56 m
A single stage impulse turbine steam enters with a velocity of 420 m/s and runs at 3300 r.p.m. If the blade speed ratio is 0.44, then the diameter of the wheel in meter will be the diameter of the wheel in meter
A single stage single acting reciprocating air compressor has 0.25 m x 1.75 m runs in 750 rpm is to deliver 0.20m³ free air per second from 101.3 kPa to 355 kPa. Calculate (a) the volume displacement (b) the volumetric efficiency (c) the isothermal work done, compression is at pV =c (d) the isothermal compressor efficiency if the the indicated power of compressor is 40kW
Problem 3: Water is fed to an inward flow reaction turbine, running at 180 rpm with a velocity of flow of 3 m/s. The diameter and width of the wheel at inlet are I m and 135 mm, respectively. Assuming the velocity of flow to be constant and radial discharge at inlet and outlet, find, (a) work done per kN of water, (b) power developed by the turbine,