In a similar experiment, the mass of 3 PB tablets was measured to be 3.1177 g. The tablets were crushed, and 2.9862 g of the powder was transferred to a beaker and reacted with HCI. After filtration, the filtrate was transferred to a 50-mL volumetric flask and diluted with water. 10.00 mL of this stock solution was combined with 0.2 M NagPO4. The resulting precipitate weighed 0.2694 g after drying. What is the mass of BSS per tablet in mg? Round your answer to 1 decimal place.

In a similar experiment, the mass of 3 PB tablets was measured to be 3.1177 g. The tablets were crushed, and 2.9862 g of the powder was transferred to a beaker and reacted with HCI. After filtration, the filtrate was transferred to a 50-mL volumetric flask and diluted with water. 10.00 mL of this stock solution was combined with 0.2 M NagPO4. The resulting precipitate weighed 0.2694 g after drying. What is the mass of BSS per tablet in mg? Round your answer to 1 decimal place.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

A solution of sodium hydroxide is standardized against potassium hydrogen phthalate (molecular mass = 204.224 g mol-1). From the following data, calculate the molarity of the NaOH solution. The mass of the KHP is 0.7840 g. Before the titration the buret reading was 0.8400 mL and afterwards it was 39.20 mL. A 85.12 mL sample of a solution of sulfuric acid, H2SO4, is neutralized by 59.82 mL of the NaOH solution from the problem above. Calculate the molarity of the sulfuric acid solution.
A science teacher needs to determine the concentration of an old, unmarked bottle of hydrochloric acid. She prepares a base titrant by dissolving 40.0 g of potassium hydroxide in 500.0 mL of water. The base is pipetted into a 28.00 mL sample of the acid, which also contains phenolphthalein as an indicator. The solution turns from clear to pink after the addition of 7.34 mL of base. What is the concentration of the hydrochloric acid?
A student begins a titration experiment by filling her first buret with unknown acid to the 1.12 mL level. She fills her second buret with base, NaOH, and records an initial volume of 0.08 mL. At the end of the titration experiment and after the pale pink endpoint is obtained, she records her final volume of acid in the buret as 18.85 mL, and the final volume of base in the second buret as 28.74 mL. In the first blank below, please indicate the volume of acid used in her experiment. In the second blank, please indicate the volume of base used. For both answers, please report your answer WITH the correct number of significant figures or decimal places, and WITHOUT a unit. Question 1 options: ___________ answer #1 ___________answer #2
On their third titration trial, the CHM 111 student used 18.80 mL of 0.205 M NaOH(aq) to neutralize 25.0 mL of HCl(aq). Calculate the molar concentration of the HCl solution to the correct number of significant figures.
In a lab, you diluted a sample of bleach to 1/10 concentration in a 250 volumetric flask. Then quantitatively transferred 25 ml of the 1/10 concentration diluted bleach into a beaker and titrated it with a standard sodium thiosulfate solution that has a molarity of 0.1215M. You repeated this 3 times. The data below is the amount of sodium thiosulfate that was titrated in the 3 runs. Calculate the molarity in each run of the diluted bleach and the concentration of undiluted bleach sample. Titration 1: 45.55 ml Titration 2: 45.67 ml Titration 6: 45.58 ml
You add 12.5mL of a 5.00M stock solution of sodium hydroxide to a 500mL volumetric flask and dilute to the mark with distilled water. What is the concentration of the resulting solution?
A 5.00-mL sample of vinegar was pipetted into a flask, two drops of phenolphthalein indicator were added, and the acid was titrated with 45.62 mL of 0.1008 M NaOH. If the density of the pipetted acetic acid solution was 1.004 g/mL, what was the percentage of acetic acid in the sample? MW HOAc =60.1 g/mol
A 1.53 g sample of a mixture of FeCl2 and Fe(NO3)2 is treated with excess AgNO3(aq). The precipitate is filtered off, dried and weighed. The dried precipitate weighs 1.92 g. What is the percentage by mass of FeCl2 in the original mixture? Your answer must be accurate to two significant digits. Keep several extra digits in your calculations and round off only at the end. Do not include the percent sign (%) as part of your answer. Molar masses (in g mol−1): N, 14.01 O, 16.00 Cl, 35.45 Fe, 55.85 Ag, 107.9
A student prepares a dilute solution of sodium hydroxide, NaOH (aq), starting with 6 M sodium hydroxide. She then titrates a 1.372 g sample of KHP with the dilute sodium hydroxide solution, NaOH (aq), to a phenolphthalein end point. 1. If the titration required 21.84 mL of sodium hydroxide, NaOH (aq), calculate the molar concentration of the sodium hydroxide solution, NaOH (aq). (Remember that KHP is potassium hydrogen phthalate, KHC8H4O4, NOT potassium hydrogen phosphorus!) 2.The student uses the same sodium hydroxide to titrate 10.00 mL of vinegar to a phenolphthalein end point. If the titration required 27.48 mL of sodium hydroxide, NaOH (aq), calculate the molar concentration of acetic acid, HC2H3O2 (aq), in the vinegar. 3. Calculate the mass percent of acetic acid, HC2H3O2 (aq), in the vinegar using the molar concentration for acetic acid, HC2H3O2 (aq), determined in part b and assuming the density of the solution is 1.01 g/mL.
Suppose a group of volunteers is planning to build a park near a local lake. The lake is known to contain low levels of arsenic (As). Therefore, prior to starting construction, the group decides to measure the current level of arsenic in the lake. If a 11.7 cm³ sample of lake water is found to have 172.3 ng As, what is the concentration of arsenic in the sample in parts per billion (ppb), assuming that the density of the lake water is 1.00 g/cm³? concentration: ppb One of the volunteers suggests hiring an on-site water treatment company to remove the arsenic from the lake. The company claims their process takes 2.98 days to remove 31.30 kg of arsenic from a water source. Calculate the total mass, in kilograms, of arsenic in the lake that the company will have to remove if the total volume of water in the lake is 0.950 km³. total mass: kg