• In a sheet metal forming press the shape to be formed is hemispherical cup of radius 15 cm in 2mm thick mild steel sheet. The force required to deform sheet is 8 kN. The forming hammer should approach job from a distance of 30 cm. The production rate required is 240 components/hr. Calculate and suggest the following specifications of the various hydraulic components used: a) Hydraulic cylinder (bore & length) b) Pump pressure and flow rate c) Electric motor HP considering 75% pump efficiency d) Reservoir size e) Size of pump inlet and discharge tubing

Q: Von mises and tresca agree in pure shear

A: In machine design, mainly five failure theories are used to relate stress with the strength of…

Q: e provided data wherever you need. mitted power = 0.050 MW, speed = 500 rpm, Modulus of Elasticity =…

A:

Q: 3. A calender machine used to add materials when preparing rubberhas 18 in.diameterrolls. The rolls…

A: Given:diameter of roll, d=18 inspeed, N=60 rpm

Q: = 2. The bending stresses on an element are: om = 25,00 psi or= 21,667 psi. There is a stress raiser…

A: ASME ellipse criterion:- ASME ellipse criterion is a theory of failure used to design component…

Q: By considering a notched metal bar as an example, explain (with the aid of diagrams), how you would…

A: The development and propagation of fractures in a material owing to cyclic stress is known as…

Q: A hydraulic press is used to apply 500 lbs of force to press fit an assembly. The cylinder has a 2"…

A: The objective of the question is to calculate the flow rate required to retract the hydraulic press…

Q: Use the provided data wherever you need. (transmitted power = 0.050 MW, speed = 500 rpm, Modulus of…

A:

Q: A double acting cylinder is used to transfer work-pieces in a production machine. Both the extend…

A: Given:Force needed, F=3500 NRod diameter, d=15 mm or 0.015 mPressure, P=6 barFriction force=10 % of…

Q: What is the force required to punch a 20-mm diameter hole in a plate that is 25 mm thick? Shear…

A:

Q: A steel rotor of a gas turbine of 400mm outside diameter, 150mm inside diameter and 25mm thick is…

A: INTRODUCTION: Shrinkage can also result in problems in cast goods, including failure and leaking.…

Q: During drawing process, using the Ao=5mm2, Af =4 mm2, K=200 MPa and n = 0.20, the average flow…

A:

Q: A draw frame has a delivery speed of 820 m/min and a total actual draft of 8. Six slivers (each 415…

A: Total actual draft = 8, Each silver is fed to draw the frame and capacity of each silver = 415…

Q: -4 cm inner diameter from

A:

Q: ((transmitted power = 0.050 MW, speed = 500 rpm, Modulus of Elast %3D GPa, Modulus of Rigidity = 70…

A:

Q: Q1/ A cuber of the type of open-end đies arranged in a ring, has 66 dies, 32x32x150 mm. a-Calculate…

A: Turning operation is the manufacturing technique that is done on a lathe machine. In this operation,…

Q: (a) A teacher, design supervisor, examining a design of a student, point out to him that the shaft…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: Your vessel has a displacement of 10 000 tons and a beam of 60 feet. You observed that her rolling…

A: Given: vessel displacement = 10000 tons beam of vessel (B) = 60 feet Rolling period (RP) = 20…

Q: 1. A shaft made of steel having an ultimate strength of Su is finished by grinding the surface. The…

A:

Q: Q8) A wire of a perfectly plastic material has a starting diameter of 3 mm. Assume no friction and…

A: Given   Initial diameter, D = 3 mm     Final diameter, d = 1 mm Find  Number of passes, N

Q: A 1.5m mean diameter flywheel, 600 kg weight changes its speed from 240 rpm to 230 rpm during…

A: Given that, Mass of the flywheel, m=600 kg,Mean diameter of flywheel, Dmean=1.5 m,Speed of the…

Q: Compare the force required to draw (25mm×6mm) capper strip to 45% reduction of area with that…

A:

Q: A cold rolling operation is to be used to reduce a 50 mm thick and 200 mm wide copper plate. The…

A: given; initial thickness(h1)=50mminitial width(w1)=200mmentry velocity(v1)=15m/minexi…

Q: n a wire drawing operation diameter of a steel wire is reduced from 10 mm to 8 mm .The mean flow…

A: Given:Initial diameter of steel wire, Di=10 mmFinal diameter of steel wire, Do=8 mmThe mean flow…

Q: A moterial is crushed in a Gyratory crusher such that the averoge size of particle is reduced from…

A:

Q: .For the 50 mm shaft shown in figure. 2. If a torque T and moment M are lied to the shaft, use the…

A:

Q: Q1/ A cuber of the type of open-end đies arranged in a ring, has 66 dies, each 32x32x150 mm.…

A: Turning operation is the manufacturing technique that is done on a lathe machine. In this operation,…

Q: a pipe varies jointly with the internal pressure and the diameter of the pipe, and inversely with…

A: Given data as per question The stressσ in pipe varies jointly with the internal pressure(P) and the…

Q: If the Poisson's ratio of an elastic material is 0.8 the ratio of modulus of rigidity to Young's…

A: This question is based on the concept of elastic properties of material. Poisson's ratio= 0.8

Q: The new line of go-karts will have a two-stroke internal combustion engine. The engine generates 35…

A: Given: Power = 35 hp = 26.0995 kW Mean speed = 2000 rpm To find: Design a flywheel

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.