In a R-L-C AC circuit, R= 44 Ohm, ZL- j 46 Ohm, ZC= -j 38 Ohm. Supply voltage is v= 38 sin( 44 t). Calculate the magnitude of Z. Your Answer:

Q: Known Vsat for LM741 ± 14V for source voltage Vs ± 15V. If Vi1 = 3 V and Vi2 = 4 V, Ri1 = Ri2 = Ro2…

A:

Q: Mask design. Silicon solar cell made of Al thin-film electrodes on silicon using lift-off…

A: According to the question, we need to draw a mask design for a silicon solar cell made of Al…

Q: A household three-way switch is used to allow lights to be controlled from two loca- tions (e.g., at…

A: Three way switch type is SPDT single pole double throw. Two switches

Q: A conductor installed from a bonding/grounding bushings that's used to provide a conducting between…

A: Given the conductor is used to provide the raceway and enclosure.

Q: Q explain briefly with drawing the principal of zener region operation and the applications of zener…

A: consider the given circuit;

Q: Which of the following layer is below the drift layer in non bunch through IGBT ? O a. p-layer O b.…

A: The IGBTs without n+ buffer layer is called as non-punch through IGBTs.

Q: For self bias configuration. Solve for Ib and Ic. ... 4 RC 15002 RB VCC 16V 100A/A 80 k2 Re 10002…

A:

Q: Ise Kirchoff's junction rule to give the equations of current in figure. 30 40 50

A:

Q: Assume an ideal-offset model for the diode with VON = 1 V. = Given Is 2 mA and R = = 1 k, find the…

A: The resistor, The source current, Diode voltage,

Q: What is the relative permitivity of the insulator used in a capacitor given that a copper resistor…

A: Specific resistivity of copper= 1.7x10-8 ohm-meter total resistance R=136 milliohms capacitor rating…

Q: 9 10 7 8 What is true and important about a good voltmeter? Find the thevenin resistance for the…

A:

Q: Find Fourier trmefarm of e

A: GivenX(t)=e-2tu(t-1)

Q: c. Clipper is a circuit designed to prevent a signal from exceeding a predetermined reference…

A:

Q: In static characteristics, is specified at only one particular point of scale.

A: Static characteristics: It is used to measure the quantities that are slowly varying with time or…

Q: Q1 For the op-amp circuit shown below V is approximately equal to 10 V 105 N 95 2 1 MN 100 kN 100 k2…

A:

Q: Which of the following layer is below the drift layer in non bunch through IGBT ? O a. n-layer Ob.…

A: n- is the called drift layer because The forward blocking voltage in the IGBT depends on this…

Q: If a Si diode at room temperature (25°) has a leakage current Is = 46 nA, k = 5,800, and V₁ = 0.65…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: (02) DC Si Diode Circuit. (Course: Electronic Devices and Circuit Theory) What is the minimum value…

A:

Q: Refer to the National Electrical Code or the working drawings when necessary. Where applicable,…

A: We are authorized to answer one question at a time, since you have not mentioned question you are…

Q: 8. are electrons at the outer shell. a) Inside shell electrons b) Conductor electrons c) Outside…

A:

Q: Consider the circuits shown in figure 4. Each represents a configuration of LEDs driven by a voltage…

A: Given:Different configurations of LEDs,To determine:The intensity of other LEDs if one of the LED is…

Q: Sketch the energy band diagrams of metal-semiconductor junctions at equilibrium for the following…

A: In metal-semiconductor junctions at equilibrium, the energy band diagram illustrates the alignment…

Q: 9. Use this information to answer Question 9-12: Consider a step pn junction made of silicon. The…

A: As per our company guidelines we are supposed to answer only first 3 subpart kindly repost other…

Q: Aluminum has a resistivity of 10.6×108 Om at 20°C. What will the resistivity of Aluminum when then…

A:

Q: *Use 4 decimal places. **Note D1 is Germanium, D2 is Silicon, For the circuit below, determine the…

A: In this question,  Find the voltage across diodes and limit resistance. And find the current in each…

Q: We want to investigate how the field strength will be with air as dielectric and with steatite. A…

A: Parallel plate capacitor, Line voltage, VL=24 kV. Area of parallel plate A=1 m2. Distance between…

Q: (2) Use The current used for a No-Load condition is Partial Load. The current for used for a Full…

A: Current drawn by the machine during no load condition is minimum (nearer to zero). Hence, the…

Q: In what ways are integrated circuits better than discrete ones.

A: Brief description: In the above given question they want to know the advantages of integrated…

Q: 2. Determine Vo and I for each circuit in Fig. 9-21. Assume that each of the diodes i these circuits…

A: Diode- It is the minimum forward voltage across diode after which diode start conduction. Diode is…

Q: Determine Vo and I, for the networks below. 15V Ip Si AD1 Si D2 +V, 2.2k. -5V

A:

Q: Circuit shown in figure if (B = 50) tind The values of CIc). and of Then express The change in value…

A:

Q: 200V shunt generators has an armature resistance of 0.02ohms and a shunt resistance of 50ohms. At…

A: In this question we will find armature current of dc shunt generator.....

Q: The terminal potential difference will be greater than its emf when it is * OIn open circuit O Being…

A:

Q: For Si, list two donor elements and two non-metallic acceptor elements: TWO DONOR ELEMENTS TWO…

A: The Donor elements have a total of 5 valence electrons and hence, the group V elements are…

Q: acitance of

A:

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.