estion 5"In a process plant,a DC motor is operating at its rated load and 1800 rpm. If its speed regulation is 5.8 percent. What will be its speed(in rpm) at no load condtion?O equal to 1800O less than 1800O more than 1800O None of optionA Moving to another question will save this response.AR40C

Rated speed is given, Nfl=1800 rpm Voltage regulation is given, VR=5.8%=0.058

"In a process plant,a DC motor is operating at its rated load and 1800 rpm. If its speed regulation is 5.8 percent. What will be its speed(ih ipm) al O equal to 1800 O less than 1800 Omore than 1800 O None of option

"In a process plant,a DC motor is operating at its rated load and 1800 rpm. If its speed regulation is 5.8 percent. What will be its speed(ih ipm) al O equal to 1800 O less than 1800 Omore than 1800 O None of option

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: following: a)Types

Q: 1. An AM standard broadcast station has a Lower sideband and an upper side band frequency of 770KHz…

Q: Speed control of a 140 V, 1.68 kW DC motor şingle phase thyristor full wave AC-DC It is made by the…

A: Given details are Motor is permanent magnet DC motor. It is controlled by single phase full wave…

Q: 3. Calculate the torque develop of an induction motor supplying the following power and speeds: a. 5…

A: Given the power and speeds, Pm=T2πN60T=Pmx602πN

Q: Find the starting current (in Ampere) of 146 V DC series motor if the armature resistance = 0.6 ohm…

A: armature current of DC series motor=(terminal voltage -back emf)armature resistance+ series field…

Q: Why when I have a small, desired speed of a Dc MOTOR the measured speed has small error while if I…

A: A motor that operates by the Direct current and converts energy from direct current into mechanical…

Q: A DC series motor rotates at 1200 rpm and draws 40 A at 240 V. The armature and field resistances…

A: The speed of the motor, The current drawn by the motor,The terminal voltage,The iron and friction…

Q: A 1200 rpm, 700V Series DC motor has an armature resistance of 20 and the field resistance of 90. If…

A: efficiency = output powerinput power = input power - lossesinput power input power to motor =…

Q: 1200rpm, series DC motor has armature resistance of 50 and field resistance of 80. Find the…

A: From given efficiency we will calculate current drawn by the motor. input power= terminal voltage*…

Q: (C)-Draw the mechanical characteristic of shunt and series DC motors. dienas SKINVER

A: Graph are provided,x and y axes are labelled with typical notations.

Q: By decreasing the stator voltage of induction motor to 80% of its rated voltage, the maximum torque…

A: Torque is directly proportional to the square of voltage. Let the reduced voltage be V'. Then , V'=…

Q: the forward torque will be equal to the backward torque at slip of two one none of the mentioned O…

A: In this question, Choose the correct options What is slip if forward torque and backward torque are…

Q: A 280 V shunt motor has an armature resistance of 0.3 Q and field resistance of 115 Q. At no load,…

Q: 16 In the speed current characteristics of DC series motor, the speed is decreasing when the…

Q: If the losses of the armature wingdings of dc motor which is running at 1200 RPM is neglected and…

Q: A 200 V dc motor takes 50 A in series and is operating at a speed of 1000 rpm when full of…

A: Given, A dc motor with, Terminal voltage, V=200 V. Armature current, Ia=50 A. Operating speed,…

Q: A permanent magnet de commutator motor has a no load speed of 6000rpm when connected to 120V supply.…

A: Given- Armature resistance = 2.5 Ω. Speed N=6000 RPM, Supply E=120 V, Torque T=0.5 N-m, Supply…

Q: 500 V shunt motor has an armature resistance of 0.3 Q and field resistance Of 250 Q. Determine the…

Q: A direct current shunt motor develops 10 HP at 8000 RPM when drawing a line current of 40 A at 220…

A: Given- 10HP @ 8000 RPM.I=40 A,V=220 V, To Find- Efficiency & useful torque.

Q: discuss how the dc motor is used in electric toothbrush

A: Electric toothbrush: It is a toothbrush that uses rapid automated bristle movements, such as…

Q: A) Why is the power factor of a lightly loaded 3-phase squirrel-cage inductio a) most of the power…

A: A. At light loads power supplied to induction motor consists of magnetization or reactive power…

Q: An eight-pole 60-Hz ac induction motor produces an output power of 2 hp and has rotational losses of…

A: Given data, The value of frequency of motor is f = 60 Hz. Number of poles P = 8. The value of…

Q: A 250 V DC series motor takes 40 A and runs at 1000 RPM. Find the speed at which it runs if its…

A: The back emf of the given DC series motor is, Eb1=V-Ia1Rf+RaV=250 VoltsRf=0.25 ΩRa=0.25 ΩIa1=40…

Q: If the losses of the armature wingdings of dc motor which is running at 1200 RPM is neglected and…

Q: A direct current shunt motor develops 10 HP at 8000 RPM when drawing a line current of 40 A at 220…

Q: mmc UD D in ne IN T זרזבט רזבײַזומ ממזונור מרמנcבסי Q.94 For a 3.6°, 2-o bipolar stepper motor, the…

A: Given- A 3.6o, 2-ϕ bipolar stepper motor- Stepping rate=200 steps/second, To Find- The rotational…

Q: A 1200 rpm, 700V Series DC motor has an armature resistance of 20 and the field resistance of 90. If…

A: Efficiency = output power/ input power. Total losses = cupper loss + rotational losses.

Q: A 100 V DC separately excited motor has armature resistance 2 ohms and voltage constant of 0.6 V…

A: V = 100 V Ra = 2 ohm Kb= 0.6 V/rad/s T= 20 Nm Kt = 50 Nm/s

Q: A 4 pole, 300 V Series Wound DC Motor developing 25 HP and 81.57 N-m torque runs at a speed of 750…

Q: 2.. A three-phase 60 Hz asynchronous motor runs at 890 rpm at idle and 840 rpm at full load. ww w w…

A: Frequency f= 60Hz Speed 890rpm at idle Find the number of poles Slip at nominal speed What happed…

Q: 22 A 400 V, 60 Hz, Induction motor has a starting torque of 125 % and a pull-out torque of 375 %…

A: Given a 400 V, 60 Hz, induction motor has, Rated torque = τ. Starting torque, τst=125 % of τ=1.25τ.…

Q: Which of the characteristics, given in the figure, is of a series DC motor?*

Q: Q18 / Draw The torque-speed characteristic of a series DC motor.

Q: What are the principle characteristics of DC series motor and DC compound motor, and what are its…

A: Introduction DC motor: DC motor converts the DC electrical input energy in the form of mechanical…

Q: Explain the difference in the Torque-Speed Characteristics of DC Shunt and series Motors. b+ A 120 V…

A: DC Motor: DC Motor is an electromechanical device which converts electrical energy to mechanical…

Q: a 20kw, 200v dc shunt motor has an electrical efficiency of 86% and an armature resistance of…

A: It is given that: Po/p=20 kWV=200 Vη=86 %Ra=0.25 Ω

Q: A 100V shunt motor is developing 6Hp while operating at an overall efficiency of 86%. The armature…

Q: 4. If the no load speed of DC motor is 1300 rpm and full load speed is 1100 rpm, then its voltage…

A: Given, A DC motor with No load speed = 1300 rpm Full load speed = 1100 rpm

Q: 2. A universal series motor, when operating on 220 V DC draws 10 A and runs at 1400 rpm. Find the…

A: Given data: Voltage (V_dc) = 220 V (DC) Current (I_dc) = 10 A Speed (N_dc) = 1400 rpm Voltage (V_ac)…

Concept explainers

DC Series Motors

A DC motor is a type of electric motor which converts electric energy into mechanical energy. The forces that are produced by the magnetic field are what those common types of motors rely upon. Either electro-mechanical or electronic, all types of DC motors have some internal mechanism to change the current direction in part of the DC motors. As the DC motors could be powered from existing DC lighting power distribution systems, these motors were the first form of motors widely used. By changing the strength of the current in its field winding or by using a variable supply voltage, the speed of the DC motors can be controlled over a wide range.

Question

100%

estion 5
"In a process plant,a DC motor is operating at its rated load and 1800 rpm. If its speed regulation is 5.8 percent. What will be its speed(in rpm) at no load condtion?
O equal to 1800
O less than 1800
O more than 1800
O None of option
A Moving to another question will save this response.
AR
40C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

22. A) Why is the power factor of a lightly loaded 3-phase squirrel-cage induction motor very low? a) most of the power supplied to the motor at light loads is magnetization or inductive power b) most of the power supplied to the motor at light loads is resistive power c) most of the power supplied to the motor at light loads is capacitive power d) none of the above B) What happens to the power factor as load is increased on the motor? a) the power factor increases b) the power factor deceases c) remains the same
A DC motor should be operated in a strong field which is due to the What happens to if suddenly goes a) nothing, it continues rotating b) it over speeds c) it stops rotating current if moter if rotating to zero. as before
NEED IN 5 MINS PLEASE URGENT :(( The rotational losses in a dc motor is equal to 400 W. What is the efficiency if the motor output is 1 kW?
A 2 hp 50 Hz 3-phase 220 V delta wired induction motor has a full-load rated speed of 1400 rpm. a) How many poles does the motor have? b) Calculate its rated output torque. c) What is the slip at full load? d) If the current is 6.37 A with a power factor of 0.79 at full load, what is the efficiency of the motor? e) Calculate the torque and approximate speed at ½ load. f) If a variable frequency drive were used to control the speed of this motor, what is the approximate maximum speed for the load from e)? What frequency would the drive be set to? Please answer all subpart either dislike is ready please all subpart in short please
For a particular application, a 4-phase stepper motor must be capable of stepping in 22.5° increments. How many poles must it have? What is the rotational speed in RPM, when the control unit of the motor supplies 200 pulses per second ? Select one: O a. P = 4 poles, and nm = 750 RPM O b. P = 6 poles, and nm = 666 RPM O c. None O d. P = 8 poles, and nm = 520 RPM Clear my choice
Question A dc series motor with a resistance between terminals of 1 0, runs at 800 rpm from a 200 V supply taking 15 A. If the speed is to be reduced to 475 rpm for the same supply voltage and current the additional series resistance to be inserted would be approximately
The full-load slip of a 54 Hz, a four-pole induction motor is 4 %. The power converted from electrical to mechanical form in the motor is 23.1 kW. What is the induced torque in this motor?
A 400v series motor working with unsaturated field is taking 60 A and running at 840 rpm. The total resistance of the motor is 0.1 ohm. At what speed will the motor run when developing half-full load torque.
a 220 V dc shunt motor has armature resistance 0.23 ohm, on load it takes armature current 40 A and turnes at 720 rpm, if the flux of motor is reduced by 10% without changing the load torque . Find the new speed of the motor.