In a Peloton turbine, the wheel diameter is 2 m and the denecting angle of the water is 162". The jet diameter is 165 mm. the water pressure at the nozzle is 1000 kpa and the discharge correction is not necessary. The wheel rotates at 320 rpm. Neglecting friction, find; (a) the power developed by the wheel, (b) turbine efficiency and (c) wasted water energy

In a Peloton turbine, the wheel diameter is 2 m and the denecting angle of the water is 162". The jet diameter is 165 mm. the water pressure at the nozzle is 1000 kpa and the discharge correction is not necessary. The wheel rotates at 320 rpm. Neglecting friction, find; (a) the power developed by the wheel, (b) turbine efficiency and (c) wasted water energy

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a trial run, the De Laval steam turbine at Oman Power Plant rotates at 3000 rpm. The steam is issued from the nozzle at 400 m/s and the nozzle angle is 20o. The blade speed ratio is 0.41and the friction loss in the blade channel is 15%of the kinetic energy corresponding to the relative velocity at the inlet to the blades. As a turbine engineer at that station, how do you determine the (i) power developed by the turbine for a flow rate of 10 kg/s and (ii) suitable inlet and outlet angles for the blades when axial thrust is zero. Also, how would you determine the size of the turbine wheel required? Draw a suitable velocity diagram.
Solve it quickly please
A certain hydropower plant is being supplied by river flow of 900 cubic ft/sec and the head on the site is 200 ft. To develop maximum capacity it was proposed to install 2 turbines, one of which is 1.5 times the capacity of the other. Both turbine units are assumed to have efficiency of 85%. Determine (a) the total power developed, (b) what is the power developed by turbine #1 and by turbine #2 and (c) Rotative speed of each turbine unit assuming specific speed equal to 70 rpm.
An impulse turbine operating at a net head of 2000 ft uses a Pelton wheel of diameter 12 ft and a jet flow area of 5 in. Using Bernoulli equation, find the turbine power corresponding to the best efficiency. Use velocity coefficient of 0.94 and a bucket angle of 165 degrees.
Using data given below, determine the main dimensions and blade angles of a Francis turbine. Net head=65 m, speed= 700 rpm, BHP= 400. Actual hydraulic efficiency3D 94%, overall efficiency= 85%, flow ratio= 0.18, wheel width at inlet/ wheel diameter at inlet=0.1, inner diameter/ outer diameter= 0.5. Assuming constant velocity of flow and radial discharge. Neglect area blocked by blades. Vane angle at inlet: 27° 39 33° 53 41° 82 O 52° 56
In a Francis turbine, when 6N force is applied to the disc with a radius of 0.08m, the revolution rate is 2500 rpm, the water flow rate is 8 m3 / h, the inlet pressure is 12 mSS and the outlet pressure is 0 mSS. In this case, calculate. Francis turbine efficiency
i need the answer quickly
ENPY = (+ 3.2 cm. Centrifugal pump rotates at 1500 rpm. Water enters the wings normally and exits by 38 degrees from the radial direction. The volumetric flow rate is given as 0.25 m^3/s. By accepting the yield as 100%; A centrifugal pump impeller has an inlet radius of 15 cm and a blade width of 6.3 cm. Its radius at the exit is 35 cm and its wingspan is (a2 = 38°) (Psu = 998 kg/m³) P1 + as 29 pg P2 + d2 29 pg L V² hg sûrekli= f-52g + zz + hpompa.f + hearbing + hg,toplam Re = p.V. D + z2 1.11 = -1.8 log Re 6.9 ɛ / D hkyerel = KK 29 Wmil = 3.7 hg,toplam= hx,sarekli + hx.yerel Протра H = pg z/1ẠM Nsp = (gH)³/4 ротра giris Wmil,B WmilA WR %3D PR (we PA b) Find the required shaft power for the centrifugal a) Find the manometric head provided by the centrifugal pump. pump. 28092 W 17,05 m O 42087 W 21,28 m O 38085 W 13,67 m O 45765 W 12,23 m O 35063 W 15,56 m
= (a) A centrifugal pump, with salt water as the working fluid, has the impeller blades rotating at 750 rpm. The fluid enters the blades in the radial direction, i.e. at an angle of α₁ = 0°, and exits the blades at an angle of 35° from the radial direction. i.e. α₂ = 35⁰. The inlet radius and blade width are r₁ 12.0 cm and b₁ = 18.0 cm, respectively. The outlet radius and blade width are 1₂ = 24.0 cm and b₂ = 16.2 cm, respectively. Assuming 100 percent efficiency, and if the volumetric flow-rate through the pump is 0.573 m³/s, compute the net head produced by the centrifugal pump. Furthermore, calculate the required brake horsepower in Watts. Take the density of salt water to be p 998.0 kg/m³. =
a) A centrifugal pump with an impeller diameter of 100 mm rotates at 1450 rpm. The pump delivers 0.010 m'/s of water. The width of the impeller at the outlet is 15 mm and the outlet blade angle is 130°. Assuming that the water enters the impeller axially and if the head loss is 25% of the absolute velocity head at the outlet of the impeller, determine: i) the net head produced by the pump, i) the required brake horsepower, and iii) the pump efficiency.
Derive the expression for specific speed of a turbine.