In a machine shop, the band saw blade is cutting through a work piece that is fed between the two guide blocks B (Figure P5.8). To what tension P should the blade be set if its stress is to be 35 MPa during use? Neglect the small size of the teeth relative to the blade's width. P 75 mm B 0.6 mm 10 mm

In a machine shop, the band saw blade is cutting through a work piece that is fed between the two guide blocks B (Figure P5.8). To what tension P should the blade be set if its stress is to be 35 MPa during use? Neglect the small size of the teeth relative to the blade's width. P 75 mm B 0.6 mm 10 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the loaded shaft illustrated in Figure Q4 (i). The shaft is simply supported at A and D. The shoulder fillet radius is 0.3 cm at B and C. If the shaft is subjected to a force of F-800 N, determine the following: (a) The reaction forces at the two ends of the shaft A and D. (b) The bending moments at shoulder fillets B andC. (c) The nominal stresses at shoulder fillets B and C. (d) The stress concentration factor at shoulder fillet B. (e) The maximum stress in the shaft taking into account stress concentrations. 800 N T-0.3 can A d, - 3 cm d, = 5 cm d, - 3 cm 5 cm 8 cm 8 cm 12 cm Figure Q4 (i) The reference parameters are shown in Figure Q4 (ii) in the page that follows. For 0.002 srlds 0.3 and 1.01 s Dlds 6.0, the stress concentration factor for bar bending is given as: kn -4.4 = 0.632 + 0.377 -0.14 – 0.363(P/a)" + 0.503(P/a) 1- 2.39(P/a) + 3.368(2la)* -0.5 The nominal stress is: 32M %3D nd3
Plz solve only a and b parts Hand written plz asap please..i'll rate
(BB) Q1: The shaft, as shown in Fig. is driven by pulley B from an electric motor. Another belt drive from pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The ratio of belt tensions for pulley B is 2.5. The diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable shear stress for the shaft material is 85 MPa. Taking torsion and bending factors as 1.25 and 1.5 respectively, find the shaft diameter. C # -100- A B -150-100 D TB2 All dimensions in mm. B A TAZ TAI TB1
please solve step by step and correctly
Derive the expression of Castigliano's 2nd theorem for linear displacement and slope. The bolt in Figure Q6 has a diameter of 10 mm and the link AB has a rectangular cross section that is 12 mm wide by 7 mm thick. The bolt is tightened so that it has a tension of 500N. Both members are made of steel with elastic modulus of 200 GPa. By neglecting the hole in the link and with the help of free body diagram, determine the strain energy. i) In the bolt due to axial force. ii) In the link due to bending 60mm 30mm 50mm B 7mm Figure Q6 Bolt
Figure Q2 shows the cross-section of a closed ended thick-walled cylinder with inner radius, ri, 0.1 mand outer radius, ro, 0.2 m. The cylinder is subjected to internal pressure, pi and external pressure, po.One of the design specifications is to maintain the hoop stress at the outer surface of the cylinder at zerovalue. If po = 50 MPa and by using Lame’s equations for thick-walled cylinder, (a) determine the value of pi to achieve the design specification (b) sketch the hoop, radial, and longitudinal stress variations across the wall thickness and label their values at the inner and outer radius of the cylinder (c) determine the absolute maximum shear stress existing in the cylinder wall material
1. A cold drawn mild steel, AISI 1018CD is used to fabricate the hollow shaft as shown in Figure Q1. Torque of 15 Nm and 30 Nm are exerted at B and C, respectively. The outer diameter of the shaft is D = 20 mm and the inner diameter is d = 15 mm. If the modulus of rigidity for the steel used is given as G = 78 GPa, determine: a) the maximum and minimum shear stresses at sections a-a and b-b. b) the angle of twist at end C. 0.3 m A a; B 15 Nm 0.8 m b. b: Figure Q1 с D 30 Nm
There is a person in this tutor who solved this question until part (c ) So please solve the remaining of the question
A 28 mm diameter rod with a 30 mm diameter handle as shown in Figure Q1 has two 90 degree bends. The handle is attached to the wall at 'A' while 1.8kN load is applied at the end of the rod at 'E'. Calculate Maximum Shear Stress at location 'A' and 'B' and determine it critical location. Bending load at point 'A'? Bending load at point 'B'? (Nm) Torsion load at rod; 'T'? Normal Stress due to bending load at point 'A'? (MPashear Stress due to torsion load at point 'A'? (MPa) 1st Principle stress at point 'A' (max principle stress)? (MPa Maximum shear stress at point 'B'? Critical Location? (L1) 170 $30- (L2) в 470 $28- F= 1.8kN| E 300 100 (L3) D Figure Q1
Solve it pls.
Handwritten solution with diagram Thanks