In a large reservoir, the water level is kept constant, and the water is discharged through a vertical pipe. Whole neglecting the energy losses, the flow rate flowing through the pipe and the relative pressure at points B, C, D Calculate the values.

In a large reservoir, the water level is kept constant, and the water is discharged through a vertical pipe. Whole neglecting the energy losses, the flow rate flowing through the pipe and the relative pressure at points B, C, D Calculate the values.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cast iron pipe having a diameter of 100 mm is used to fill the cylindrical tank with water at T = 25° C. The pipe has a total length of 50 m. Suppose that h = 25.5 m. 1.11 1 Neglect minor losses. Use the equation = -1.8 log [(F) ¹ 3.7 (Figure 1) + 6.9 Re Part A Determine the required power output of a pump necessary to fill the empty tank to a depth of 3 m in 6.5 min. Express your answer to three significant figures and include the appropriate units. Wout = A 5708 KW = Submit Previous Answers Request Answer Provide Feedback X Incorrect; Try Again; 5 attempts remaining ?
The water stored under 500 kPa air pressure is discharged through the hole in the bottom of the tank. Calculate the time required to drain half the water in the tank. (pwater = 1000 kg / m3, Patm = 100 kPa, D1 = 2 m, D2 = 10 cm) 1. P1 = 500 kPa 3 m Water
Water is flowing in a 3 m wide rectangular channel. A hydraulic jump occurs and the flow upstream is 360 mm deep while the flow downstream from the jump is 1300 mm deep. A) Find the discharge flowing in the channel. B) Find the energy absorbed by the jump in kW. Please answer correctly
Three reservoirs A, B and C are connected by a pipe system shown in the figure below. If the rate of flow from the reservoir A is 55 l's, and the coefficient of friction (F) for all pipes is 0.015. Find the piezometric head at point D A L2=600 m d2=20 cm D Q1=0.055 m/s L1=1200 m d1=30 cm 28 m 30 m
Please include complete solution
An oil fluid flows through pipe with a constant diameter. Determine the total energy head (in meter) at point A from the datum line 3 meters below the point B. po = 900kg/m3, PA = 50 kPa, pg = 94.10 kPa. 0.75 m A 5 m 2 m/s 30 B
SITUATION 4: Water is drained from a large reservoir using two horizontal pipes connected in series. The first pipe is 20 m long and has a 10-cm diameter, while the second pipe is 35 m long and has a 4- cm diameter. The water level in the reservoir is 18 m above the center line of the pipe. The pipe entrance is a sharp edged, and the contraction between the two pipes is sudden. Neglecting the effect of the kinetic energy correction factor, determine the discharge rate of water from the reservoir. Assume the friction factor for all pipes is equal to 0.02 and the loss coefficient is 0.05 for a sharp edged entrance, and is 0.46 for sudden contraction. 18 m Oil tank 20 m 35 m
Energy Equation: Example 2: h₂ 80 m = Datum D = 0.2 m 0.02)V² 2g L = 2000 m- = 0.02 V² D2g A horizontal pipe carries cooling water at 10°C for a thermal power plant. The head loss in the pipe is hL Q = 0.06 m³/s where L is the length of the pipe from the reservoir to the point in question, V is the mean velocity in the pipe, and D is the diameter of the pipe. If the pipe diameter is 20 cm and the rate of flow is 0.06 m³/s, what is the pressure in the pipe at L = 2000 m? Assume a₂ = 1.
Suppose the impeller in the preceding question supplies 10 kW of water power and is placed in a tank 4 m square and 4 m deep. Determine the velocity gradient G (s ¹). The water viscosity is 1.31 x 10-3 Pa-s.
Water is flowing in AF pipe (Figure 1) at a velocity of 2 m/s and a pressure of 102400 Pa, the pipe length is 100 m. If the water pressure needs to be at a pressure of 1.6 atm on a lower level. What should be the different in elevation between the upper and lower levels in order to achieve this pressure? Take the density of water 1000 kg/m3 and gravity is 9.81 m/s2, consider the energy loss.
A pipeline, 50 cm diameter and 4,500 m long, connects two reservoirs whom constant difference of water level is 12 m. A branch pipe, 1,250 m long and taken from a point distant 1,500 m from reservoir A, leads to reservoir C whose water level is 15 m below that of reservoir A. Find the diameter, in centimeters, of the branch pipe, so that the flow into both the reservoirs is the same. Assume friction coefficient ƒ = 0.03 for all the pipes.
A single -acting reciprocal pump lifts a liquid of specific weight 7.50 kN/m³ from a pressurised storeage reservoir to an overhead container. The free surface in the supply reservoir is at an elevation of 5.0 m above the centre of the pump. The ambient pressure over the liquid surface in the supply resevoir is 20 kN/m². The other relevant data relating to the pump are as follows: Length of suction pipe = 5.0 m Crank Speed= 60 rpm Diameter of suction pipe = 10 cm Length of Stroke = 40 cm Diameter of cylinder = 20 cm Atmospheric presure = 100 kN/m²(abs) Calculate the pressure in the cylinder and force on the piston at the beginning of the suction stroke.