In a hydroelectric power plant, water enters the turbine nozzles at 760 kPa absolute with a low velocity. If the nozzle outlets are exposed to atmospheric pressure of 100 kPa, determine the maximum velocity to which water can be accelerated by the nozzles before striking the turbine blades.

Q: A 3.6 liter hot pot filled with steam at 300 pKa empties through the pour spout of the pot while…

A:

Q: 4)Carbon dioxide flows steadily through a varying cross-sectional-area duct such as a nozzle shown…

A: The first step is to determine the conditions at the throat of the nozzle, where the area is…

Q: Q-3/A vessel is divided equally in two parts. The first part is evacuated, while the second part of…

A:

Q: Q-3 / A vessel is divided equally in two parts. The first part is evacuated, while the second part…

A: Given data in second part of container  mass of compressed liquid (m)  = 2.5 kg  Initial Pressure…

Q: Q-3/A vessel is divided equally in two parts. The first part is evacuated, while the second part of…

A: Given ; T= 333 K , P1 = 4 bar ,P2 = 40 KPa

Q: A centrifugal pump, driven by a DC motor, running at 100 rpm delivers 500 gpm of water against a…

A:

Q: Air is heated as it flows through a 6 in × 6 in square duct with negligible friction. At the inlet,…

A: Given data: Inlet air temperature, T1 = 700 R Inlet air pressure, P1 = 80 psia Inlet air velocity,…

Q: determine the velocity of gas jet at exit from the nozzle.

A:

Q: Steam enters a turbine at 10,000 kPa and 500 °C, and exhausts at 100 °C with an enthalpy of 2000…

A:

Q: Air inside a cylinder has increased its pressure from 100 KPa to 200 KPa. Evaluate the change in…

A:

Q: Steam at a temperature of 300C has a specific volume of 0.09765 m3 /kg. Determine the pressure,…

A: Since you have asked a multi-part question, we can provide you the solution to first three sub-parts…

Q: An auxiliary turbine receives saturated steam at 300 psia with negligible kinetic energy at the rate…

A:

Q: During the execution of a reversible non flow process the work Is -156.2 KJ. If V1 =0.845 cubic…

A: Given data as below: Work W = -156.2 KJ Volume V1 = 0.845 m3 Pressure P = -730V + 690 KPa To…

Q: 5 ft3 /s oT air is conmpressed in an adiabatic compressor from an initial state of 14.7 psi and 60…

A:

Q: A MOTORIST EQUIPS HIS AUTOMOBILE TIRES WITH A RELIEF-TYPE VALVE SO THAT THE PRESSURE INSIDE THE TIRE…

A:

Q: A Pelton wheel turbine is a type of turbine that transforms the kinetic energy of water jet to…

A:

Q: Water at the initial pressure of 1 atm and temperature of 15C is flowing through a pump. Final…

A:

Q: The entropy of steam entering the turbine at temperature 800°C and Pressure 1600 kPa is

A: Steam temperature, T=800oC Steam pressure, P=1600 kPa

Q: The turbine's inlet is connected to a steam throttling valve with inlet conditions of 3MPa and 500C,…

A:

Q: 4. In a turbo-jet engine the momentum of the gases leaving the nozzle produces the propulsive force.…

A: It is required to deterrmine the diameter of the nozzle at inlet.

Q: Air is compressed in a piston-cylinder device in a reversible isothermal process at a temperature of…

A:

Q: 10 kg/s of air enters the turbine at a pressure of 120 MPa and 910 K. The air expands Isentropically…

A: Write the given values along with the suitable variables.

Q: Su 300 L/sn 175 kPa 160 kPa . A sprayer elbow is used to throw water at a flow rate of 300 L/sec…

A: The force exerted on the elbow.Given:The pressure at the inlet is .The pressure at the outlet is…

Q: A compressor draws in 0.1 m/s of air at atmospheric conditions of 1.013 bar and 22°C and delivers it…

A: Steam nozzle is a device which having varying in cross section. In which pressure is reduced by…

Q: The thrust developed by the engine of a Boeing 777 is about 380 kN. Assuming choked flow in the…

A: Given: The thrust developed by the engine is F=380 kN. The ambient temperature is T=215 K. The…

Q: Gas turbine operates with air. At the initial state the air has pressure of 1.3 MPa and temperature…

A:

Q: An ideal gas enters a turbine with a velocity of 40 m/s through an inlet pipe with a diameter of 160…

A:

Q: Air enters a gas turbine steadily at pressure 20 kPa, volumetric flowrate 1,000 m3/s, and…

A:

Q: Air enters a compressor at a temperature of 70•C and a pressure of 10 kPa. At the exit of the…

A:

Q: Steam enter a turbine stage with an enthalphy of 3628 kJ/kg at 70m/s and leaves the same stage with…

A:

Q: Steam enters the turbine at a speed of 10 kg/s. The pressure at the inlet is 100 bar and the…

A: