In a hydraulic press, the small cylinder has a diameter of 8.00 cm, while the large piston has a diameter of 20.0 cm. If a force of 500 N is applied to the small piston, what is the force on the large piston, neglecting friction?

In a hydraulic press, the small cylinder has a diameter of 8.00 cm, while the large piston has a diameter of 20.0 cm. If a force of 500 N is applied to the small piston, what is the force on the large piston, neglecting friction?

Name: In a hydraulic press, the small cylinder has a diameter of 8.00 cm, wh
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: In a hydraulic press, the small cylinder has a diameter of 8.00 cm, while the large piston has a diameter of 20.0 cm. If a force of 500 N is applied to the small piston, what is the force on the large piston, neglecting friction?

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter15: Fluids

Section: Chapter Questions

Problem 42PQ

See similar textbooks

Similar questions

A garden hose with a diameter of 2.0 cm is used to fill a bucket, which has a volume of 0.10 cubic meters. It takes 1.2 minutes to fill. An adjustable nozzle is attached to the hose to decrease the diameter of the opening, which increases the speed of the water. The hose is held level to the ground at a height of 1.0 meters and the diameter is decreased until a flower bed 3.0 meters away is reached. (a) What is the volume flow rate of the through the nozzle when the diameter 2.0 cm? (b) What does is the speed of coming out of the hose? (c) What does the speed of the water coming out of the hose need to be to reach the flower bed 3.0 meters away? (d) What is be diameter of nozzle needed to reach be flower bed?
(a) How high will water rise in a glass capillary tube with a 0.500-mm radius? (b) How much gravitational potential energy does the water gain? (c) Discuss possible sources of this energy.
Review. In a water pistol, a piston drives water through a large tube of area A1 into a smaller tube of area A2 as shown in Figure P14.46. The radius of the large tube is 1.00 cm and that of the small tube is 1.00 mm. The smaller tube is 3.00 cm above the larger tube. (a) If the pistol is fired horizontally at a height of 1.50 m, determine the time interval required for the water to travel from the nozzle to the ground. Neglect air resistance and assume atmospheric pressure is 1.00 atm. (b) If the desired range of the stream is 8.00 m, with what speed v2 must the stream leave the nozzle? (c) At what speed v1 must the plunger be moved to achieve the desired range? (d) What is the pressure at the nozzle? (e) Find the pressure needed in the larger tube. (f) Calculate the force that must be exerted on the trigger to achieve the desired range. (The force that must be exerted is due to pressure over and above atmospheric pressure.) Figure P14.46
A host pours the remnants of several of wine into a jug a party. The host then inserts a cork with a 2.00-cm diameter into the bottle, placing it in direct contact with the wine. The host is amazed when the host pounds the cork into place and the bottom of the jug (with a 14.0-cm diameter) breaks away. Calculate the extra force exerted against the bottom if he pounded the cork with a 120-N force.
A large storage tank with an open top is filled to a height h0. The tank is punctured at a height h above the bottom of the tank (Fig. P15.39). Find an expression for how far from the tank the exiting stream lands. Figure P15.39
A tank with a flat bottom of area A and vertical sides is filled to a depth h with water. The pressure is P0 at the top surface. (a) What is the absolute pressure at the bottom of the tank? (b) Suppose an object of mass M and density less than the density of water is placed into the tank and floats. No water overflows. What is the resulting increase in pressure at the bottom of the tank?
The gravitational force exerted on a solid object is 5.00 N. When the object is suspended from a spring scale and submerged in water, the scale reads 3.50 N (Fig. P15.24). Find the density of the object. Figure P15.24 Problems 24 and 25.
A rock with a mass of 540 g in air is found to have an apparent mass of 342 g when submerged in water. (a) What mass of water is displaced? (b) What is the volume of the rock? (c) What is its average density? Is this consistent with the value for granite?
You are applying for a position with a sea rescue unit and are taking the qualifying exam. One question on the exam is about the use of a diving bell. The diving bell is in the shape of a cylinder with a vertical length of L = 2.50 m. It is closed at the upper circular end and open at the lower circular end. The hell is lowered from air into seawater ( = 1.025 g/cm3) and kept in its upright orientation as it is lowered. The air in the bell is initially at temperature Ti = 20.0C. The bell, with two humans inside, is lowered to a depth (measured to the bottom of the bell) of 27.0 fathoms, or h = 49.4 m. At this depth the water temperature is Tf = 4.0C, and the bell is in thermal equilibrium with the water. The exam question asks you to compare two situations: (i) No additional gas is added to the interior of the bell as it is submerged. Therefore, water enters the open bottom of the bell and the volume of the enclosed air decreases. (ii) The bell is fitted with pressurized air tanks, which deliver high-pressure air into the interior of the bell to keep the level of water at the bottom edge of the bell. This choice requires money and effort to attach the tanks. The exam question asks: Which scenario is better?
Review. The tank in Figure P15.13 is filled with water of depth d = 2.00 m. At the bottom of one sidewall is a rectangular hatch of height h = 1.00 m and width w = 2.00 m that is hinged at the top of the hatch. (a) Determine the magnitude of the force the water exerts on the hatch. (b) Find the magnitude of the torque exerted by the water about the hinges.
Figure P9.27 shows the essential parts of a hydraulic brake system. The area of the piston in the master cylinder is 1.8 cm2 and that of the piston in the brake cylinder is 6.4 cm2. The coefficient of friction between shoe and wheel drum is 0.50. If the wheel has a radius of 34 cm, determine the frictional torque about the axle when a force of 44 N is exerted on the brake pedal. Figure P9.27
You are pumping up a bicycle tire with a hand pump, the piston of which has a 2.00-cm radius. (a) What force in newtons must you exert to create a pressure of 6.90105 Pa (b) What is unreasonable about this (a) result? (c) Which premises are unreasonable or inconsistent?