In a four bar mechanism the link AB rotates with angular velocity of 20rad/s and angular acceleration of 100 rad/s both in clockwise direction when it make an angle of 45° with link AD which is fixed .The length of various linkages are AB=CD=400 mm,BC3D500mm and AD=750mm .Neglect the gravitational effect and friction.The mass of link is 5kg/m. Find the torque on output link B. (3) E (2) (4) A (1)

In a four bar mechanism the link AB rotates with angular velocity of 20rad/s and angular acceleration of 100 rad/s both in clockwise direction when it make an angle of 45° with link AD which is fixed .The length of various linkages are AB=CD=400 mm,BC3D500mm and AD=750mm .Neglect the gravitational effect and friction.The mass of link is 5kg/m. Find the torque on output link B. (3) E (2) (4) A (1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2
Example 4: In the mechanism shown, the crank OA rotates at 20 r.p.m. anticlockwise and gives motion to the sliding blocks B and D. The dimensions of the links are OA = 300 mm; AB = 1200 mm; BC = 450 mm and CD = 450 mm. For the given configuration, compute: 1. Velocities of sliding at B and D, 2. The angular velocity of CD, 3. The linear acceleration of D, and 4. The angular acceleration of the link CD. B w he 1050 mm
The EOM for the following 1-DOF gyroscope is: JÖ + BO + KO = Hw w is the angular velocity of the gyroscope about the input axis, is the angular position of the spin axis, H is the angular momentum stored in the spinning wheel, J is the mass moment of inertia of the wheel about the output axis, B is the viscous friction coefficient about the output axis, and K is the spring constant of the restraining spring attached to the spin axis. Determine the transfer function relating output to the input w. Case K spin axis output axis BOD Go Wheel spins at constant velocity input axis
For the four-bar linkage in the posture shown, find the angular velocities of links 3 and 4, and the velocity of point C. When w2 = 60 rad/s ccw, RAO, = RBA = 6 in, Ro.0, = RBO, = 10 in, and RCA = 8 in. %3D y 3. 4 90°
The single slider mechanism shown below has the following dimensions: the crank AB - 95 mm and the connecting rod BC-270 mm with centre of gravity D, 90 mm from B. The crankshaft has a speed of 75 rad/s and an angular acceleration of 1200 rad/s. Find: Acceleration of D and angular acceleration of CB. 125
Problem 2 For the mechanism shown if link AO1 = BC = 50 mm, AC = 200 mm, BO5 = 100 mm, and link A01 rotates at 200 rpm counterclockwise, 1- Draw velocity and acceleration polygon. 2- Velocity and acceleration for piston C. 3- Angular acceleration for link BO5. 05 01 03
For the inverted slider-crank linkage in the posture shown, crank 2 has a constant angular velocity of 160 rev/min ccw. Find the velocity and acceleration of point B, and the angular velocity and acceleration of link 4. R0402 = 12in, Rao₂ = 7in, and RBO₂ = 28in. B 15° @2 4
Problem 7 (Use relative motion analysis): The four-bar linkage is a famous one! If the angular velocity and angular acceleration of the drive link OA are 10 rad/s and 5 rad/s², find the angular acceleration of bar AB at this position. Ans: %AB = -15.99 rad/s² B 200 mm CO 15⁰ 240 mm @0, %0 0 A 80 mm 60°
Asap plz handwritten solution acceptable Need urgently The mechanism shown below consists of a 1ft radius disc BC and a 5ft long link AB. If the angular velocity and the angular acceleration for the link are given: find the angular velocity and angular acceleration of link AB.
both partt ASAP
Two shafts the axes of which intersect but are inclined to each other at 22 degree are connected by means of a universal joint. At what position in the rotation cycle of the drive shaft (i) velocity ratio will be maximum, minimum and unity (ii) the acceleration is maximum
A wheel of the F vehicle, developed for an experimental purpose, and a mechanism attached to it are shown in the figure. The speed of the center of mass of the wheel rolling without sliding is constant and v=36km/sa. A pin fixed on the wheel can give oscillating movement to the OA bar, which can rotate around the O point. In another slot above the OA bar, the DB control bar is moved back and forth via pin B. At the moment shown in the figure:a. Find the speed and acceleration vector of pin A.b. Find the angular velocity and angular acceleration vector of the OA bar.c. Find the acceleration of the DB control bar