In a crank and slotted lever quick return mechanism, as shown in Fig. 2, the driving crank length is 75 mm. The distance between the fixed centres is 200 mm and the length of the slotted lever is 500 mm. Find the ratio of the times taken on the cutting and idle strokes. Determine the effective stroke also

Q: A rotating load is directly coupled to a motor with moment of inertia Jo, and the load then…

A: Block diagram

Q: 4. Why do multi-cylinder engines have smaller flywheels than single-cylinder engines? 5. What…

A: singal cylinder engine: A single cylinder engine is a engine with only one cylinder. It consist with…

Q: For the given position of the mechanism shown in Fig. 4, determine the magnitude an direction of the…

A: according to the given details

Q: Efficiency of reducer gear train 2KW input was given at the input end at a speed of 1220 rpm f at…

A:

Q: Duestion For the rotational system :- with gears woite the differentia s, at P, in equation NI Ng j.…

A: Given-Data:-Rotating system To-Find:-Equation

Q: Find the forward and return velocities of an offset slider crank mechanism rotating at 1500 rpm…

A:

Q: Power is transmitted from the 1st shaft to the 2nd shaft with a Conical Friction coupling at 950…

A: Given: The speed of coupling, N = 950 rpm The taper angle, α = 25° The mean diameter, D = 120 mm

Q: Problem number 6 only. Thank you so much!

A:

Q: The horsepower input of the power screw. The efficiency if the weight loaded is 10 kN.

A: This is consisting of Two threads twisted together in which the pitch is equal to twice the distance…

Q: If the inertia is 80 lb-ft2, and the speed of the driven shaft is to be increased from 0 to 1500 rpm…

A:

Q: (c) A rotating load is directly coupled to a motor with moment of inertia Jo, and the load then…

A: Solution:   Both the parts are solved with necessary explanation below:

Q: A linear actuator having a in single-thread Acme screw is used to raise a load of 1600 lb. A plain…

A: Given:The diameter of the thread, The value of the load, The mean diameter of the thrust collar, The…

Q: 2) Compute the effective inertia that a clutch must transmit to accelerate a 54-inch solid shaft…

A: Introduction: The ability of a body to resist angular motion about an axis is defined as its moment…

Q: For the offset slider-crank mechanism shown in the figure, calculate (a) the length of stroke of…

A:

Q: (machine dynamic)  The variation diagram of the cutting force of the cutting work done with the…

A:

Q: Find the natural constraints for the turning crank shown below. CÂ cŷ

A: to find:the number of natural constraints.given:the figure

Q: In order to test the efficiency of reducer gear train 1 kW input was given at the input end at a…

A: Given:Torque, T=56.36 N-mInput power, P=1 kW or 1000 WInput end speed=1440 rpmspeed reduction=10:1

Q: Please solve ellaborately and include the untis in every step, show diagram and write your solutions…

A:

Q: gn a hoist equipment using a reverted epicyclic gear train shown in 1. The drum must be keyed at the…

A:

Q: tA with 12 inches diameter pulley running at 250 rp er pulley. Another pulley on shaft B 16 inches…

A:

Q: A double-threaded right-handed worm gear transmits 15 Hp at 1150 rpm. The pitch of the worm is 0.75…

A: The given information in the problem is shown in the following attached image:

Q: 7. A typical drive train for a 'geared' bicycle meant to be used on paved road (see a representative…

A: (a) Write the given data. Tf=48Df=10.5 inTs1=30Ts2=26Ts3=23Ts4=20Ts5=16Ts6=12Nf=105 rpmFf=28 lb

Q: What weight (kg) can be lifted by a double threaded screw that has an efficiency of 85% if it is…

A: Given, No. of threads in one lead = n =2 (For double threaded screw)Efficiency = η = 0.85Applied…

Q: Problem number 2 only. Thank you so much!

A:

Q: A rolling cone with a center angle of 15° turning at 240 rpm makes external contact with the second…

A: Given data: The Center angle of the first rolling cone is 2α=15°, The revolution of the first…

Q: (a) When the work done by the engine is less than the energy required the flywheel decelerates. (b)…

A:

Q: uck return mechanis is 180mm. The incli

A:

Q: In a single purchase Crab Winch, If number of teeth T1 is greater than T2 then the shaft attached…

A: we know thatVelocity ratio of single purchase crab is given byVR=Dd×T1T2for given condition neglect…

Q: In a broaching machine shown, shaft A carries a pulley 60.96 cm in diameter which is driven by a…

A:

Q: e numerical value for the ideal mechanical advantage of a bicycle with 10 teeth on e effort gear and…

A: Solution is attached below

Q: turning moment on the crank

A: Given data; A slider crank mechanism with ,crank radius, r=200 mm=0.2 mConnceting length ,l=800…

Q: a/ A pinion having 20 in volute teeth of module pitch 6mm rotutes at lo0 r.p.m. and tronrmits 1.5kw…

A: Module of gear is the measure of size of a gear. It is defined as the ratio of pitch circle diameter…

Q: Q6. Write whether each of the following is true (T) or false (F): 1- In a two stroke engine, the…

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Q: 6lb hammer of a pile driver is lifterd 5m the pilling head. If the hammer is released, what will be…

A:

Q: The secondary unbalanced force is maximum times in one revolution of the crank.

A:

Q: An inside cylinder locomotive has its cylinder centre lines 1 m apart and has a stroke of 1 m. The…

A:

Q: A worm drive transmits 15 kW at 2000 rpm to a worm gear having 90 teeth with 6mm module. The worm is…

A:

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.