**Question:**In a Δ-connected generator, the phase voltages are 208 V. What are the line voltages?**Select one:**- A. 360 V- B. 132 V- C. 120 V- D. 208 V**Explanation:**To find the line voltage in a Δ-connected (delta-connected) generator, we use the relationship between phase voltage (V_ph) and line voltage (V_line). In a delta (Δ) connection, the line voltage is equal to the phase voltage because each line is directly connected to a phase. Therefore, if the phase voltage is 208 V, the line voltage is also 208 V.**Correct Answer:** D. 208 V

The connection of the generator is ΔPhase voltage VPh=208Vasked to find the line-line voltage

Answered: In a A-connected generator, the phase…

In a A-connected generator, the phase voltages are 208 V. What are the line voltages? Select one: OA. 360 V OB. 132 V C. 120 V OD. 208 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: For the circuit in the figure, Rab =6002, Zbc = 8022+ j6022. Compute the following: a. Phase and…

Q: Suppose you have a three-phase generator that provides 120 V per phase and works at a frequency of…

A: Here we discuss the concept of power & power factor.

Q: A voltage of 200 253"8' is applied across to impedances in parallel. The values of impedances are…

Q: 1. Refer to Figure 1. A Y-connected source supplies 3 balanced 3-phase loads. The source has voltage…

A: Source is star connected. V =Vab =380 V Note: frequency is not given, we assume f= 50 HZ

Q: load 800+j0 ohms is connected across a 200 V and 50 Hz supply. Find the Power angle.

A: Given, Supply voltage is Vs = 200 V Frequency (f)= 50 Hz Impedance of load (Z) = 100 + j 0 ohm , So…

Q: In the A.C generator circuit shown in the figure below: a- Find the phase angle 02 & 0 3 c- Find…

A: Phase current and Line currents remain same in star connected system Phase voltage and line voltage…

Q: A load of 40 -j 30 is connected to a source of 100 V with a phase angle of 300, through a…

A: Given load impedance, ZL=40-j30° On comparing with ZL=R-jXC

Q: Electrical Engineering From the following circuit, analyze the power consumption of the loads and in…

Q: Assume that is(t) = 4 sin(100t + 30), R = 100, R1 = 100, R2 = 50, c = 0.5mF, and L = 0.2H. A. Find…

Q: In three phase power measurement using star connected system, reactive power can be calculated…

Q: Problem: For the cct shown find the equation of current and draw the phaser 202 diagram. 402 VR VL…

A: We need to find out current for given circuit

Q: all V R sine sine Let the voltage source be 202135, the current source be 10245 and the impedance of…

A: In this question, We need to determine the value of resistance R if angle of current flow in this…

Q: ) Find the ICA load current. b) Give the line voltage Vab. c) Calculate the total complex power…

A: In the circuit a) Find the ICA load current. b) Give the line voltage Vab. c) Calculate the total…

Q: Problem 6: Given the circuit below, find the total complex, average, and reactive power absorbed by…

A: In this question, We need to determine the total complex power, average power and reactive power.…

Q: j4 2 -j2 0 Vx3 20 +. ZL +)4/0° V

A: In this question we need to find a Zl for maximum average power transfer to Zl

Q: From the given circuit, take V₁ = 240, Z₁ = 20 - j3 ohms. Find the phase currents and line ZL…

A: In this question, A 3phase balance source supply to 3 phase balance load. We need to find the…

Q: It is required to know 1. The Real Power of the Generator: 2. The Reactive Power of the Generator 3.…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Problem 4: A three phase motor draws 30 kVA at 0.80 power factor lagging from a 480 V three phase…

A: The data are given as KVA ratingS1=30kVA,Power factorpf1=cosϕ1=0.8 laggingso, ϕ1=36.87°.1) Without…

Q: . Calculate the voltage regulation of a 230V, three phase alternator supplying the following loads…

A: As per our policy i have attempted first three sub-parts Given data: Voltage regulation is: 230 V

Q: = 10 + j8 Q per phase as shown in Figure below. Determine the value of IAC What is the value of IbB?…

A: The given circuit diagram is shown below:

Q: A wye-connected three-phase alternator is rated at 1.5MVA, 2300 volts. It has a synchronous…

A: Given, A Y-connected, 3-ph alternator has, Apparent power (S)= 1.5 MVA Terminal voltage (Vt)= 2300 V…

Q: Calculate the generator powers, the power losses, and . : draw the phasor diagram for the following…

Q: A three – phase load of 2.0 MW with P.F of 0.8 lead is connected to a 12.46 kV grid. Find the…

Q: A 415 V, 56 Hz 3-phase supply is connected to a 3-phase star connected balanced R-L load each of…

Q: Find the load current IAB b) Find the line voltage Vbc c) Calculate the total complex power on the…

A: Find the load current IAB Find the line voltage Vbc Calculate the total complex power on the loads

Q: 4. A single phase load draws a current of 30 / 35 deg A. The voltage across the load is 220/ 75 deg…

Q: Balanced 3-phase Delta connected voltage sources are given in the figure. Find the star-connected…

A: The delta star transformation is done to simplify the circuits. The line voltage in star connection…

Q: A star connected reflector supplies a delta connected load. The impedance of the load branch is (8 +…

Q: In the A.C generator circuit shown in the figure below: a- Find the phase angle 0₂ & 0 3 c- Find…

A: In Balanced system, The vector sum of net current at the common node will be…

Q: Find the load current IAB b) Find the line voltage Vbc c) Calculate the total complex power on the…

A: ) Find the load current IAB b) Find the line voltage Vbc c) Calculate the total complex power on the…

Q: Suppose you have a three-phase generator that provides 120 Vac per phase and works at a frequency of…

A: In delta connection line voltage is equal to phase voltage.

Q: Find the total real power dissipation in a balanced delta-connected system. Phase voltage is 100V…

A: Given: A balanced delta connected system Phase voltage, Vph=100 V Load impedance, Zph=175 Ω Power…

Q: A delta connected load of impedances (6 + j9) ohms each is supplied through a line having an…

Q: A 200 V single phase circuit has an apparent power of 5 KVA and reactive power of 4 KVAr. Then find…

Q: rom the given circuit, take V₁ = 240, Z₁ = 20 - j3 ohms. Find the phase currents and line urrents.…

A: The given three phase system is balance. So we can analyse the circuit by per phase analysis.

Q: 12. Refer to the circuit below. The alternator has a line voltage of 240 V and the load has an…

A: In this question, Star connect alternator is supplied to Delta connected load. Find the phase,…

Q: If in a Y- connected ac generator, each phase voltage has a magnitude of 90 Vrms, what is the…

A: Given a Y-connected generator with, Each phase voltage has magnitude, Vph=90 V rms.

Q: A 200 ohm resistor is connected to a 5 millihenry inductor at 60HZ. Find the total impedance and the…

Q: A single phase circuit is supplying the two loads, Load1 draws a real power of 450 kW at a power…

A: From power triangle KVA S=Active power (P)power factor(cosθ). and KVA S =…

Q: A single – phase load of 96 kW with PF of 0.6 lag is connected to a 4.16 kV single – phase network.…

A: In this question, we need to determine the magnitude of current of this load in ampere. We know,…

Concept explainers

Three-Phase Transformers

Three-segment transformers are a type of transformer used to transform voltages of electrical systems into three ranges. Two type transformers are shell-type transformer and core type transformer. In brief, it could be described because of the exquisite kinds of configurations.

Transformer

Ever since electricity has been created, people have started using it in its entirety. We see many types of Transformers in the neighborhoods. Some are smaller in size and some are very large. They are used according to their requirements. Many of us have seen the electrical transformer but they do not know what work they are engaged in.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Line to line voltage

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

IN THE CIRCUIT OF THE FIGURE THE LOADS ARE THE FOLLOWING: LOAD A: 4 KVA WITH F.P = 0.8 IN DELAY LOAD B: 2.4 KVA WITH F.P = 0.6 IN DELAY LOAD C: 1 KW AND 500 VA INDUCTIVE DETERMINE: a) Current I b) The power factor of the combination.
4
Which type of load results in a power factor (PF) of 1? a, Capacitive b, Inductive c, Resistive d. Reactive
a) Find the load current IABb) Find the line voltage Vbcc) Calculate the total complex power on the loads.
A delta connected load (Figure 2) has an impedance Z is(12 + j35) ohms. If the applied VAB voltage is 380 V with -50º phase . Get the current IC and load IAB current.
Two impedances, A and B, are connected in parallel across a 120 V AC supply. The total current and the current in each impedance are adjusted to 20 A. The power drawn by A is doubted that of B and the power factor is lagging. Determine the power factor of A. Ans: 0.650 lagging
A single phase circuit is supplying the two loads, Load1 draws a real power of 350 kW at a unity power factor and Load 2 draws reactive power of 15 kvar at a power factor of 0.74 leading. Find the Apparent power of the Load 1 and Load2.Apparent power of Load1 kVA?Answer for part 1 Apparent power of the load 2 kVA ?
14- A load 100+j0 ohms is connected across a 200V and 50 Hz supply. Find the Power factor. a. Unity b. 0.4 c. 0.8 d. 0.6
In a balanced three-phase system Vôn 120Z – 45° V. What are Ven and Vab?
3. a) Find the current i, in the circuit in the following circuit by using source transformation. b) Using the result obtained in (a), work back through the circuit to calculate the power for the 1A source. Determine if the current source supplies or absorbs power. 10 kN 3 kN 5 kN 50 V 15 kN (+ )1 mA $20 kN i $15 kN 6 kN
2. For the following system shown in the figure, calculate: a. The current through each phase of the load. b. The total real and reactive power of the three-phase load. c. The power factor at the load side. A 220 V 20° 220VL-120° U8 vol 152 I 220 VI20° 9. M.
5. complete solution