Illustrative Example 7.9 A single-stage axial flow gas turbine has the lowing data Mean blade speed 340 m/s Nozzle exit angle 15° Axial velocity (constant) 105 m/s Turbine inlet temperature 900°C Turbine outlet temperature 670°C Degree of reaction 50% Calculate the enthalpy drop per stage and number of stages required.

Illustrative Example 7.9 A single-stage axial flow gas turbine has the lowing data Mean blade speed 340 m/s Nozzle exit angle 15° Axial velocity (constant) 105 m/s Turbine inlet temperature 900°C Turbine outlet temperature 670°C Degree of reaction 50% Calculate the enthalpy drop per stage and number of stages required.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q8: In Kaplan reaction turbine produces (70kW) at (370 r.p.m). The hub and tip diameter are (0.4m and 0.8m) respectively. The flow velocity is (2.8 m/s), find peripheral velocity and discharge.
Q8: In Kaplan reaction turbine produces (70kW) at (370 r.p.m). The hub and tip diameter are (0.4m and 0.8m) respectively. The flow velocity is (2.8 m/s), find peripheral velocity and discharge.
Q3: A single stage, double acting air compressor running at 1000 rev./min delivers air at 25 bar and 170°C For this purpose, the induction air conditions can be taken as 1.013 bar and 15°C, and the air deliver at rate 0.25 m³/min. The clearance volume is 3% of the swept volume and the stroke bore ratio is 1.2/1. Calculate the bore and stroke, the volumetric efficiency, the indicated power, and the isothermal efficiency.
Please show complete solution. Thank you!
A gas turbine stage develops 3.4MW for a mass flow of 27 kg/sec. The stagnation pressure and temperature at the stage entry are 772 kPa and 100OK. The axial velocity is constant throughout the stage, the gases entering and leaving the stage without any absolute whirl. At the nozzle exit, the static pressure is 480kPa and the flow direction is at 72°. Let C,=1.148, R=0.287. Determine the following: a) the axial velocity, b) the degree of reaction for the stage given that the entropy increase in the nozzles is 13 J/(kg °C),
Please don't provide handwritten solution ......
9.2 The inlet stagnation temperature of a centrifugal compressor rotating at 10,000 rpm is 20°C. The inlet flow is axial and the blades are radially tipped at the exit. It is required to produce a stagnation pressure ratio of 2.8 when the total to total effi- ciency is 0.85. It has 19 blades and a mass flow rate of 3.0 kg/s. Through measure- ments, the density of air at the exit of the impeller is found to be 1.5 kg/m³. The width of the blades at the exit is 1 cm. Calculate the following: (a) power required to drive the compressor, (b) diameter of the impeller, and (c) absolute Mach num- ber at the exit. Use Stanitz's equation for the slip coefficient. Ans: 355 kW; 0.694 m; 0.897
7.7 Consider a turbine consisting of two stages. The overall pressure ratio is four and the inlet conditions are 500 K and a pressure of four atmospheres. Assume that each stage has the same stage efficiency and pressure ratio. If the isentropic tur- bine efficiency is 85%, calculate the stage efficiency. Ans: Nst- 83.3%; n,> Nst
Combustion gases with k=1.35, Cp =1107 J/(kg.K) and R= 287 J/(kg.K) flow at stagnation pressure and stagnation temperature of 390kPa and 1150 K respectively, flow through a 90o IFR turbine to an exit static pressure of 100 kPa. The total to static efficiency is 80% and the flow leaves the stator choked (Mach Number=1). The relative velocity at the inlet to the rotor is radial and the flow leaves the turbine without a swirl. Find (a) the work delivered per unit flow rate, (b) the impeller tip velocity and (c) the flow angle at the inlet to the rotor.
Looking at just the bypass flow of a large turbofan, assume that Min = 0.8, Tin = 225 K, Mdot = 90 kg/s, PRF = 1.6 and hF = 0.90. Let P0 = 25 kPa. Determine: (a) Vexit, (b) Thrust from the bypass flow assuming that it is chocked (MEX = 1).
mgt for a range extender produce 70kw power, pressure ratio=3.2, inlet compressor temperature=300k, recuperator effictiveness =0.7, using hydrogen fuel,could you help me to calculate turbine inlet temperature, thermal efficiency. many thanks.