(iii) A single conductor of length 60 mm is positioned at a 45° angle to a magnetic field of density 50 mT. The conductor experiences a force of 100 µN. (a) Sketch the conductor with the current and the magnetic field indicating their vector directions, and the direction of the resulting force. (b) What is the value of the current flowing in the conductor?

Q: Thanks for your helping

A: It is our pleasure that you get what you were looking for.

Q: Describe the job of the Board of Electrical Engineering in one sentence. Note: The Board of…

A: It is asked to describe the job of the Board of Electrical Engineering in one senctsen.

Q: Question (1): With proper example and circuit diagram briefly explain the following theorems.  (i)…

A: The evaluation of electrical circuits containing different circuit components and power sources…

Q: How many nodes are there? image d.png ... 1.5 0 20 50 2 A( )5 A Answer _nodes

A:

Q: Given a single-family residence with a general lighting load of 33,500 VA. What is the demand…

A: NEC (National Electricity Code ) has defined demand factors for different types of load

Q: An electric train system (ETS) in Japan with a span of 10 miles long is connected to a two…

A:

Q: the abbreviation MCB stand for? (2) Make a neatly labelled drawing to show how a stove sub-circuit…

A: A stove sub-circuit typically involves dedicated wiring to safely handle the high power requirements…

Q: Based on the computed TEC (Thevenins Equivalent Circuit), What is the voltage across the load R3, in…

A: In this question,  We need to determine the voltage across the resistance R3  in Volt.  We are…

Q: Determine the size and type of wire to he installed to a building with temperature that reaches…

A: Here ratings of loads are given for a single phase 230 V source. We need to determine the size and…

Q: What is the acceptable minimum value of leakage current of HI-POT Test of electrical cables. Can you…

A: According to the question,what is the acceptable minimum value of leakage current of HI-POT Test of…

Q: Find % Regulation for the given readings VR(Line to Line ) = 394 Volts, Vs(Line to Line ) = 458 %3D…

A:

Q: Type N connectors are used in moisture environments and used with consumer audiovisual electronics…

A: True.

Q: Find the value of unknown. 5:100 —___:10

A: The solution is given below

Q: Inverting Op-Amp R₁ R₁ Vo R2 R4 998.48m V R2 R3 9.9844 R1 R4 2.1244 out of phase A(gain) A(gain)…

A:

Q: (iv) When doping a semiconductor n type, the bandgap of the material will: Increase Decrease /…

A: Due to the doping , Fermi level will shift towards the conduction band .

Q: The ________parameters may not reflect the actual operating conditions but simply provide an…

A: For the AC analysis of BJT or MOSFET based circuits, It is important to convert it into different…

Q: Q4: Write the following compound words in the correct form as (one word, two words, or hyphenated):…

A: AirportFossil fuelCheck-in

Q: What can you do in the sim

A: You can do several things in the sim is as follows;  1.You can recreate yourself and friends in the…

Q: Fill in the blank to supply the missing/s words to complete the sentence. Electrical that comes…

A: Mostly power station produces the electricity in AC form it is because the distribution of the…

Q: Given a single-family residence with a general lighting load of 33,500 VA. What is the demand…

A: NEC (National Electricity Code ) has defined demand factors for different types of load

Q: What are the Rules in Performing Laboratory experiments in the Electrical Engineering Laboratory?…

A: It's vitally important to take safety precautions when working with electricity. Safety must not be…

Q: Could you answer this question in details and giving examples if possible. Thanks a lot.  - Explain…

A: we need explain Arbitration in CAN BUS.

Q: And a typical phone service installation, a drywall is constructed beneath the_. A. Weep hole b.…

A: In this question we need to find a a correct option

Q: Determine Reg in Ohms at the (a,b) terminals for the following circuit. Round your answer to the…

A:

Q: P-channel MOSFET is basically a following device. a. voltage operated O b. low-frequency operated O…

A: MOSFET is controlled by the application of GATE pulse .  GATE pulse controls the conduction state of…

Q: Printer circuit boards are functionally tested after being filled with semiconductor chips, One…

A:

Q: where did the 100 come from? Thank you.

A: In the given solution Xc<<1.5k Where Xc is  reactance of the coupling capacitor .

Q: Describe the job of the Board of Electrical Engineering in one sentence.

A: The solution is given

Q: A room measures 4mx5mx5m and the air in it has to be always kept 20 C0 lower than that of the…

A: Given Data : Volume of the room = 4mx5mx5m density of air = 1.27  kg/m3 specific heat of air  =…

Q: 200 200 20 0.53

A:

Q: Look at the photo and answer the questions

A:

Q: Discuss as to how you would connect your landline and mobile to the local telephone exchange using…

A: Mobile Telephone Switching Office(MTSO) An operations center that connects the landline PSTN system…

Q: Show the following units in scientific notation. e.g ) Five Kilometre (km) = 5 x 103 m 1) One…

A: Consider solving the problem by using the second notation (which decides the exponential power of…

Q: Draw bread board connection diagram for full adders along with tables and pin configuration of ICs…

A: Full adder truth table: Thus, Sum, S=X⊕Y⊕Cin and Carry, Cout = (X*Y) + ((X⊕Y)*Cin) So, the circuit…

Q: The parameters of the _________equivalent circuit are defined in general terms for any operating…

A: In this question,   We need to choose the correct options The parameters of the _________equivalent…

Q: How Rth connected with the load resistance, explain

A: RL will be  connected in series with  RTH  as shown in the example.

Q: Still confused about how you calculated the current. Could you please elaborate a little? thank you

A:

Q: 4. current overloads. " and are used to protect circuits against

A: In this question, we need to fill the blanks. What are the name of devices which are used to protect…

Q: Could you answer this question in details and giving examples if possible. Thanks a lot.  - Explain…

A: The Controller Area Network (CAN bus) is a standard automotive bus system designed to allow…

Q: Find the value of unknown. 5:8 — ____:10

A: The solution is given below

Q: Explain what this matching box is. Describe the parts

A: The given diagrams are shown below. It is asked what is this matching box and also it asked to…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.