II. SOLVE THE TOTAL CURRENT, Ir. (OHM'S LAW) SHOW THAT VRI + VR4 = 110 V. (VOLTAGE DIVIDER) IV. SOLVE THE CURRENT IN R4, I. (CURRENT DIVIDER) III. V. SHOW ALL COMPUTATIONS. R, = 60 N R, 40 Ω R,20 Ω ww W 110 V R4 = 50 N RT IT Vs VR1 VR4 Vri+VR4 I (in R4) (V) 110 (ОНМ) (A) COMPUTED MEASURED 110 % ERROR

Q: When a ground wire is connected to an interior gas piping system and the underground portion of the…

A: Given:When a ground wire is connected to an interior gas piping system and the underground portion…

Q: After reduction, the current - caring capacity of a condenser is referred to as the___. A. ambience…

A: Given: After reduction, the current carrying capacity of a conductor is referred to as the ___.

Q: What spaces are not included in floor area when calculating the load in volt amperes per square…

A: For calculating the load, first evaluated the total floor area. And according to the NEC , the total…

Q: The voltage drop across a resistor is 6.0V when a current of 3.0A flows across the resistor. The…

A: Given  Voltage drop across the resistor V=6 v The current in the resistor is I=3 A

Q: answer correctly or I'll give down vote 206. Describe the function of the electronic parking brake…

A: The Electronic Parking Brake (EPB), also known as the electric parking brake, is a technology that…

Q: E. Use this graphic for question 12 L1 L3 3mH 5mH L2 6mH

A: The solution is given below

Q: 4.a. The ___ calculated load is rarely placed on an electrical system. A. optional B. standard C.…

A: An electrical load is a part of a circuit or an electrical component that uses electricity.…

Q: 4) Calculate the value of the resistance Rled in Circuit #1, to ensure that a GREEN LED will have a…

A:

Q: Fill in the blank: Electrical hazard boots are made up of highly materials.

A: Electrical Hazard boots are used to prevent the shock

Q: IS it a requirement to have a light ixture outside the garage door for a vehicle? O No Yes For two…

A:

Q: What dimensions are used when measuring the area of a building? See NEC 220.12.

A: Referring to the NEC 220.12, the floor area is evaluated using the outside of the building…

Q: using the base of 2 to answer following subtraction:  1000 base 2 -101 base 2 ________________

A: According to the given question, it is required to determine the binary subtraction of the two given…

Q: This is a general question: How do smaller electrical engineering labs relate to building a…

A: Smaller electrical engineering labs can be very helpful in building a relatively larger system. This…

Q: Q.) Figure below divider bras amplifier Circult. Givent the model Parameter : gm = 5omS emitter (CE)…

A: Brief description: In the above given question they have mentioned an NPN common emitter amplifier…

Q: What is meant by Electric Bid Package?

A: Bid package means the collection of the pertinent portion of the construction documents into a…

Q: . Explain about Fuel cells?

A: Fuell cell

Q: You wish to turn on the two LEDs located at the outside of the LED pack, so the first thing you will…

A: Al means lower 8bits of the accumulator here, we want to turn on the two LEDs located at outside of…

Q: Does ‘a three digit color coding of resistor values’ limit producible resistor value ranges? Why? If…

A: Solution Yes color coding of resistor values limit the resistor value range. In colour coding of…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.