II. READING A VOLTMETER Indicate the voltage reading of the voltmeter below Directions: Write your answer on the space provided. VOLT AC/DC What is the reading? Vhe Whalen 30 20 50 290 AC1N BATTERY W-375 PANIDA Proper Pointer Position 10 250 201002000

Q: How to calculate voltage % error in electric circuit

A: Consider the formula for the percentage error in resistance is, ∆RR×100 Consider the formula for the…

Q: This question is from the subject Digital Logic Design. Assume your register number SF20-BEC-xxx…

A:

Q: what is the process on how to read an analog meter

A: Let us first understand what is an Analog Multimeter is - A PMMC meter is an analogue multimeter. It…

Q: How to construct a voltmeter by galvanometer?

A: Voltmeter - A voltmeter is a device, used to measure the potential difference between two ends of…

Q: What is the circuit in the given 1 point diagram called? R VIN D1 D2. Vo VRI I VRZ

A: In this circuit there is no capacitor is present .

Q: D1 D2 R1 5V 1K Determine the voltage across the resistor R1. (assume LED forward voltage is 2.1…

A:

Q: Explain with reference to the components in the circuit and point P why the warning lamp is on when…

A: To Explain with reference to the components in the circuit and point P why the warning lamp is on…

Q: explain briefly and consicely the importance of tolerance in resistors

A: Tolerance of resistor is the nothing but how much is the resistance value measured of its actual…

Q: A thermistor has a: a. positive output voltage. b. negative output voltage. c .positive…

A: A thermistor is an electronic component that is sensitive to temperature changes and is often used…

Q: To make a Moving iron instrument to read voltage, its should be increased. O a. Series resistance O…

A: Moving iron instruments are used to measure the current in a circuit. To measure voltage in MI…

Q: 22. a) Describe how the following sensors are used to measure temperature. i) RTD

A: Any system can be autonomous or manual. A system is called autonomous if the output is independent…

Q: What is DF04m? How to use in lighting dimmer system?

A: DF04m is a single-phase bridge rectifier. It has 4 pins having a peak reverse voltage of 400 V and a…

Q: thyristor used in a half wave rectifier used 50 KV , with firing angle 30° , total sistance load 5…

A: *Keeping a note ?as per our company guidelines we are supposed to answer ?️only first 3️⃣ sub-parts.…

Q: The basic reason why a full wave rectifier has a twice the efficiency of a half wave rectifier is…

A: The basic reason why a full wave rectifier has a twice the efficiency of a half wave rectifier is…

Q: In your own understanding what do you understand by step down transformer

A: Electrical machines can be either generator or motors. They can be either Ac machines or DC…

Q: If a resistive load is supplied from a single phase half wave rectifier, if a supply voltage is…

A: we will derive Rms and average voltage for output voltage. power output=Vrms2R.

Q: Identify the input and output of the thermistor. a. Voltage and temperature b. Voltage and…

A: The thermistor is a special type of resistor, where the resistance value is the function of…

Q: Explain the theory of voltmeters sensitivity and current's gain of the ammeter?

A: Voltmeter sensitivity is defined by the reciprocal of the amount of current required for full scale…

Q: What is the maximum value of the potentiometer? And What project can do using potentiometer? Explain…

A: It is asked to explain in brief about the maximum value of a potentiometer. It is aslo asked in…

Q: Q2/ Rectifiers can be classified according to a number of different factors explain briefly.

A: Rectifier is a electrical device which is used to convert Alternating Current to Direct Current.…

Q: Describe the function of voltmeter and ammeter

A: Voltmeter and ammeter is an instrument which are used in an electrical or electronic circuits. -The…

Q: Explain with a neat block diagram the measurement of temperature using Thermistor (measuring…

A: In this question, we have to write about thermistor construction, resistance temp characteristics…

Q: Moving Iron meter displays value. (a) RMS (b) average (c) peak (d) instantaneous

A: Moving iron instrument measure RMS value.

Q: How does a voltmeter differ from a potentiometer? What type of meter is the Corning- 10 pH meter?

A: A voltmeter and a potentiometer are two different types of measuring instruments used in electrical…

Q: (a) Determine the colour bands and indicate the resistance range values (minimum - maximum) for each…

A:

Q: 72. If the input frequency to a 3-phase rectifier is 50 Hz, then output will have a frequency of (i)…

A: Given: Input frequency of a 3-phase rectifier, fin=50 Hz

Q: Explain the operation of each of the following Devices Thyristor Diode 11.

A: i) we have to explain the Thysristor, it is consist of foure layer of semiconductor device it is…

Q: An alternating voltage, given by v = 100 sin 314t is connected to a full-wave rectifier. The average…

A:

Q: O 63.7 volts

A:

Q: Thermistor &

A: Temperature- A measurement of the heat and cold in a body is termed as temperature. The units in…

Q: Compare a three-phase half-wave controlled rectifier with a three-phase full-wave controlled…

A:

Q: When is it necessary to switch the multimeter/voltmeter ranges in measuring voltage?

A: An ammeter is a device that measures the current inside the electrical circuit. It's name comes from…

Q: 13 - Resistance thermometers should be immersed in a minimum of ..... to ..... times their outer…

A: In this question we need to choose a correct option.

Q: b) If only LSB is "1". Draw 5-bits Ring counter, then write all states it with clock pulses

A:

Q: The waveform shown is to be displayed on a digital storage oscilloscope screen. If you set the…

A: According to the question, for the given waveform as shown belowWe need to find the voltage of the…

Q: If a resistive load is supplied from a single phase half wave rectifier , if a supply voltage is…

A: The solution can be achieved as follows.

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.