II - Digital Modulation / PCM 1. Write the Binary Data (encoded value) for each sampling periods indicated on the table below. 2. Use the table provided on this file as your answer sheet. 3. Include in your answer sheet a copy of your school ID or any ID (with signature) and your signature 4. Note that SAMPLED VALUE (amplitude) should be in volt unit. 5. Deadline will be 6:30 pm, November 30, 2021 15 1111 14 1110 13 1101 12 1100 11 1011 10 1010 1001 1000 0111 0110 5 0101 0100 0011 0010 0001 0000 T1 T2 T3 T4 TS T6 7 T8 19 T10 T11 T12 T13 T14 Sampling Points Sampled Value Quantized value| Encoded Value T1 T2 T3 T4 TS T6 T7 T8 T9 T10 T11 T12 T13 T14

II - Digital Modulation / PCM 1. Write the Binary Data (encoded value) for each sampling periods indicated on the table below. 2. Use the table provided on this file as your answer sheet. 3. Include in your answer sheet a copy of your school ID or any ID (with signature) and your signature 4. Note that SAMPLED VALUE (amplitude) should be in volt unit. 5. Deadline will be 6:30 pm, November 30, 2021 15 1111 14 1110 13 1101 12 1100 11 1011 10 1010 1001 1000 0111 0110 5 0101 0100 0011 0010 0001 0000 T1 T2 T3 T4 TS T6 7 T8 19 T10 T11 T12 T13 T14 Sampling Points Sampled Value Quantized value| Encoded Value T1 T2 T3 T4 TS T6 T7 T8 T9 T10 T11 T12 T13 T14

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1o11 An analog signal with a bandwidth of 4.2kHz is to be converted into binary PCM and transmitted over a channel. The peak signal to quantization ratio at the receiver output must be at least 45dB. What will be the output bit rate?
o Develop the relevant schematic diagram in order to build the Astable Multivibrator using 555 Timer circuit. o According to the proposed schematic, write the mathematical equation for the T- High, T-Low, frequency and Duty cycle of the generated wave.
Q27) Quantization noise can be reduced when the size of quantization level is decreased. a. False b. True DIGITAL COMMUNICATIONS Course.
Write the following acronyms in full and Explain it main function. 1. LCD 2. PWM 3. MHz 4. RFU 5. LED 6. VIN 7. ICS 8. GND 9. STBY 10. VM
I need to solve point 2.
3. Explain disadvantages of ASK modulation system.
1.Which method is the only form of pulse modulation that is used in a digital transmission system? Explain. 2.What are the four most common methods of pulse modulation?
Q1) Choose the Correct Answer The output pulse width of a 555 timer is determined by the externally connected and C. capacitor, load resistor. B. load resistance, capacitor. O A. power supply, resistor. O D. input resistor, capacitor. An Analog Signal is continuous in both and A. Frequency, power. O D. Time, frequency. O C. Modulation, power. B. Time, amplitude.
(a) Suppose that the BI/RBO input line was connected to ground on the 74LS47 BCD- to-seven segment decoder and all other input lines were connected as shown in Figure 3. Determine the effect this would have on the display. (b) Assume that the switches in Figure 3 are set to binary 1000, but the display shows a zero. What are possible causes for this error? Four DIP switches +5.0 V 1.0 ΚΩ MSB LSB w 330 Ω www 330 Ω 330 ww 330 Ω +5.0 V 7447A +5.0 V R's=330 Voc Anode a w a Lamp test ba ww b BI/RBO CO www RBI Outputs d w e ww e f w ww 8 DUBA BCD inputs GND MAN72 seven-segment display
3. What is the type of demodulation we used to demodulate SSB signal (part-A). Explain your answer.
Answer the question quecly please Digital circuit
16) For the CRO display of a pulse waveform, the time/cm is on 18.7 ms/cm and the volt/cm switch is on 5 V/cm. The width of one complete cycle is 16.2 cm and the height of the pulse is 3cm. The time period will be___________________ seconds. 30294.00 0.33 0.00 0.30