If you were working with a set of project specifications prepared in CSI Format, under what division numbers would you find the following subjects?_______ Plumbing _______ Sheet metal fabrications _______ Project meetings _______ Contractorsubmittals _______ Painting _______ Piling _______ Roof flashing and sheet metal _______ Butler buildings ______ Alarm systems

Q: Please describe the quality control of concrete construction.

A: Any structure to be durable, high strength and also for a good view, much-needed factor is quality…

Q: Give and Discuss some of the new innovations or discoveries related to concrete and its application…

A: Concrete is a development material made out of concrete, fine totals (sand) and coarse totals…

Q: What is the term for the process of reinforcing a material with fibers?

A: Continuous Fiber reinforcement is a process where fibers are integrated into a base material to…

Q: What would be the best material for burglar bars and how would it be protected from corrosion

A: Most burglar bars are made of metal, usually steel, aluminium, or iron. But The best material used…

Q: What are the purposes of the various types of drawings used for the design and erection of…

A: The purposes of the various types of drawings used for the design and erection of steel framed…

Q: Explain Vibratory Hammers

A: The vibratory hammer: Vibratory Hammers is a device which is used ro drive the sheet piles into the…

Q: Explain the function of metal reinforcement and how the metal reinforcement treatment process

A:

Q: How to install Fiberglass insulation on ceiling and walling?

A: Fiberglass insulation- Fiberglass is the cheapest way to provide insulation on ceilings and walling.…

Q: more description about Critical safety Hazards (roof truss installation and re-sheeting work

A: The space above a room providing support to roof with help of structural member is known as roof…

Q: Select appropriate materials and assemblies for interior walls, partitions, and ceilings?

A: Answer:- Interior wall materials :- A wall material is a finish applied to wall of home to achieve…

Q: Define the term Fastener Spacing?

A: Fastener Spacing : Pitch is centre to centre spacing of the fasteners in a row, measured along the…

Q: Using online information, write a one-page, double-spaced article on the useof fiber-reinforced…

A: Fiber reinforced plastic is also known as fiber reinforced polymer. It is a composite material made…

Q: 1. Draw the cross-section of a trunk of a tree and label the parts.

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: What are the curing methods in common use?

A: Curing means applying water to concrete during initial period in sufficient amount to achieve its…

Q: Mention 11 natural fiber ropes

A: Natural fiber rope refers to a type of rope which are made from plant-based materials. These ropes…

Q: Sealing Joint seals In the Exterior Walls and whats its uses.

A: Joint sealers area unit accustomed shut open joints to stay water associated air out (both exterior…

Q: What is the purpose of regulations related to volatile organic compounds in coatings?

A: Question is based on Volatile organic compounds . Volatile organic compounds are the chemicals…

Q: Visit buildings under construction when floor finishing crews are at work. Observe the tools and…

A: The tools and procedures used in flooring works are:

Q: List the following standard dimensions/properties used in the Philippines for rebars: Standard…

A: All steel members expected to construct the design are manufactured and raised from shop and…

Q: Accessories for gypsum board construction.

A: Across all houses, gypsum board platforms have a critical function: fire safety. The gypsum board is…

Q: One wood product/item which have FIVE different joint connections (L-joint, rabbet, mortise and…

A: The following are the main joints in wood

Q: Use technical information on industrial plywood to make construction product decisions?

A: One class is known as construction and industrial. Plywoods in this class are used primarily for…

Q: Explain briefly the material selection criteria and the materials which are used to manufacture 1.…

A: Material selection criteria : An efficient material selection criteria satisfies  efficient…

Q: How is Silica gel manufactured?

A: Silica Gel is a non-crystalline form of highly porous silica which is used for the following…

Q: What is the standard test procedure to determine the timber grain?

A: Loads will be used in two areas in the third grade of space from each poor support of the two…

Q: Define why Load cells are used ?

A: Load  cells are transducers that are generally used in electronic weighing machines these are mainly…

Q: 10) In case of architectural restrictions, the designer must: A) Place the rebars periodically B)…

A: Warning  is being given before answering,  However I do my best.  I try to give good explanation…

Q: Please provide the enough information and definition of these construction terms:  Reinforced…

A: As per our guideline we are supposed to give  only first three answer of this question because this…

Q: Q)What are the components of a 3D cement construction printer and a 3D metal printer?

A: The components of a 3D cement construction printer and a 3D metal printer are: 1.Extruders :…

Q: Explain the process for repairing concrete walls or damaged surfaces ?

A: Solution: The methods of repairing concrete walls : 1. Epoxy Injection: this method is basically…

Q: General Specification for Civil Engineering Works (1992 Edition) Clause 15.09 specifies that tying…

A: Answer Plain steel tying wire mainly used for the reinforcement adjacent to class F4 and F5 finish

Q: Explain how hollow metal doorframes are secured to walls and floors?

A: If the doors are to operate appropriately, the installation of doors and frames is a procedure that…

Q: Which layer of road construction can metallurgy slag be used instead?

A: Metallurgy slag is a by-product of smelting and other metallurgical process due to the impurities…

Q: Explain the working of impingement scrubbers?

A:

Q: commonly Which floor system-one-way joist floor or two-way joist floor-is more used in contemporary…

A: The given Question is , Which type of Floor system is most commonly used in construction . We have…

Q: Do plumbing fixtures weaken the strength of a component where it is built inside

A: A plumbing fixture is any plumbing component, such as a faucet, that has a specified usage and…

Q: Describe the common types of pre-engineered metal building systems.

A: Pre-engineered metal building  Pre-engineered structures have a wide range of advantages and uses.…

Q: identify and describe the importance in construction of conducting the following ASTM procedure…

A: Concrete temperature test  The temperature of fresh concrete may be measured using ASTM C1064 to…

Q: What is wood flooring and what are its characteristics? What is the difference between plank…

A: What is wood flooring and what are its characteristics?What is the difference between plank flooring…

Q: make a report about glass blocks

A: Multiple units can join holes in basements and rooftops using glass blocks cast in a reinforced…

Q: Why are polymer pipes widely used?

A: 1.Polymer pipes are more efficient to manufacture in terms of energy consumption, and are non toxic,…

Q: ​Dwayne's Welding and Fabrication have decided to start a new line of workbenches to sell.​ Dwayne's…

A: The weight of nuts bolts or welding material which ever is used is not accounted into consideration.…

Q: SECTION C 1. Name any three saws that are used for cutting timber manually. [3] 2. Explain the…

A: Step 1: Step 2: Step 3: Step 4:

Introduction to Engineering Design

Students are often confused with engineering and design. The term engineering design has two words with different meanings, engineering, and design. The term engineering implies applications of laws and principles of science to design and analyze physical structures and components. In civil engineering, students apply the concept of physics and chemistry to design and build structures and buildings. In engineering disciplines, the term design means determining the dimensions, loads, and associated influences on the component due to the applied loads such as stresses and deformations. The estimation of such parameters is crucial to make the component or structure foolproof.