If you have an empty burette in a burette clamp, in what order do you do these steps to fill the burette with liquid (either water for washing, or the titrant)? Drag the steps below into the correct order. Step 1: Close the tap. Step 2: Step 3: Step 4: Step 5: Step 6: Step 7: Return burette to burette clamp. Remove burette from clamp. Hold burette with top below eye level. Put plastic funnel into top of burette. Fill burette with liquid. Remove plastic funnel.

If you have an empty burette in a burette clamp, in what order do you do these steps to fill the burette with liquid (either water for washing, or the titrant)? Drag the steps below into the correct order. Step 1: Close the tap. Step 2: Step 3: Step 4: Step 5: Step 6: Step 7: Return burette to burette clamp. Remove burette from clamp. Hold burette with top below eye level. Put plastic funnel into top of burette. Fill burette with liquid. Remove plastic funnel.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Procedure: Step 1: Pipet 25 mL of prepared sample solution, which has been prepared into a 250 mL Erlenmeyer flask. Step 2: Add 3-5 drops of phenolphthalein indicator solution to the sample solution in the 250 mL Erlenmeyer flask. Step 3: Rinse the buret with three 10 mL portions of standardized 0.1 M HC1 acid solution, before fill this acid solution into the buret and record the initial volume of this acid solution in the burette. Step 4: Titrate the sample solution with the standardized 0.1 M HC1 to the endpoint and record the final volume of this acid in the burette. (Note: phenolphthalein endpoint is from pink color to colorless) Step 5: Repeat the titration for two more times. Step 6: Repeat the same procedure from step 1 to step 5 by using methyl orange as an indicator rather than phenolphathelein. (Note: methyl orange endpoint is from orange to red color). Calculate the alkalinity of the sample for both the indicators and potentiometric method using the following equation: [Alk]…
Which of the following are properties of a good recrystallization solvent? Check all correct answers. Group of answer choices boiling point of solvent < melting point of crystals boiling point of solvent > melting point of crystals Crystals are soluble in solvent at low temperature and soluble at high temperatures. Crystals are soluble in solvent at high temperatures but insoluble or slightly soluble at low temperatures. Solvent boiling point is about room temperature. Impurities should be either soluble at all temperatures or insoluble at all temperatures. An abundant amount of crystals must be recoverable from the solvent.
46. Which zinc solution is saturated? a. 1x10-5 M ZnCO3 (Ksp=1.0x10-10) b. 4.0x10-6M Zn(OH)2 (Ksp=3.0x10-16) c. 1.5x10-4M ZnC2O4 (Ksp=2.7x10-8) d. 4.0x10-13 M ZnS (Ksp=2x10-25)
What is the concentration of FeSCN2+ in each standard solution? (Show ALL calculations for each solution) Stock Solution of the concentration of FeSCN^2+ is 0.00200 M
Help please, the data is in the second picture.
It was not helpful because the question asked about adding a chemical during water treatment. please answer it clearly. thank you
A _____________ passes through a semipermeable membrane.
Procedure A: Molarity (M=g/MM/L) Step 1. Place one-eighth of a teaspoon (this weighs approximately 0.5 grams) of NaCl (table salt) in the graduated cylinder provided. Then add distilled water to that graduated cylinder until the level of the water reaches 45.00 mL. Mix thoroughly about 1 minute. Pour solution into a somewhat clear cup. Remember what this looks like for Procedure B. Questions: Is this a saturated solution? Why or why not? Take a picture and insert a picture (compress your image) of your solution here. Save this solution for Step 2. Calculations: Determine the Molarity of this solution using the formula M = g/MM/L. You know the grams (one-eighth of a teaspoon weighs approximately 0.5 grams), look up the Molar Mass of NaCl, and convert your mL to L to solve the problem.) Show your calculations for Molarity here. C % 31 D < hp & * ✔
What is cloud point of a polymer or surfactant? A) Cloud point is the temperature below which the polymer / surfactant is insoluble B) Cloud point is the pH above which polymer precipitates C) Cloud point is the concentration above which polymer/surfactant precipitates D) Cloud point is the temperature above which polymer/surfactant precipitates
Please fill in blanks as shown on problem!!
There is a/n _______________ in solubility as temperature goes up
Based on a grade 11 chemistry student, answer the following questions: Use the data below to evaluate whether nitrates or phosphates could have been involved in the fish kill. Which month had the highest river water temperature? 2. Which month had the lowest river water temperature? 3. How would the temperature of the water likely affect the solubility of dissolved solid solutes? 4. Which month had the most rainfall? 5. Which month had the least rainfall? 6. In which months would you expect to have more runoff from the fields to the river? 7. In which months would you expect more dissolved solutes in the water? Explain. 8. The fish kill occurred in December. a. What was the average water temperature and rainfall for November and December? b. What would you expect farmland to look like during this month? c. Would you expect much fertilizer runoff during these months? Why? 9. How do nitrates and phosphates generally cause fish kills? (Look back at your previous…