If you have an empty burette in a burette clamp, in what order do you do these steps to fill the burette with liquid (either water for washing, or the titrant)? Drag the steps below into the correct order. Step 1: Close the tap. Step 2: Hold burette with top below eye level. X Step 3: Put plastic funnel into top of burette. Step 4: Fill burette with liquid. Step 5: Remove plastic funnel. Step 6: Remove burette from clamp. Step 7: Return burette to burette clamp.

If you have an empty burette in a burette clamp, in what order do you do these steps to fill the burette with liquid (either water for washing, or the titrant)? Drag the steps below into the correct order. Step 1: Close the tap. Step 2: Hold burette with top below eye level. X Step 3: Put plastic funnel into top of burette. Step 4: Fill burette with liquid. Step 5: Remove plastic funnel. Step 6: Remove burette from clamp. Step 7: Return burette to burette clamp.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Filter paper Saturated KNO; solution 259 Figure 1. Experimental apparatus. Experimental Procedure Part 1. Copper and Zinc Metal 1) Select a piece of copper and a piece of zinc metal wire from the containers in the hood. 2) Clean the surface of the metal wires with the steel wool. Wipe clean with a dry paper towel. 3) Obtain a plastic well plate. Fill one well with 10 drops of the Copper ion solution from the dropper bottle. Label this well with a Sharpie marker so that you remember which solution you filled it with, 4) Repeat step 3 with Zinc ion solution. Select a well right next to the well in step 3 so that the two wells with Copper and Zinc ion solution are right next to each other. 5) Obtain a small dry strip of filter paper. You may have to cut a large piece of filter paper down to the appropriate size. It should be exactly this big C It's OK to tear the filter paper with your hands. Using the drop bottle, saturate the filter paper strip with KNO; solution. Gently place one end…
Anion Test - Nitrate (NO3‾) Procedure : Mix H2SO4 4 M into 5 drops of NO3‾ solution (NaNO3 0.5 M) until the solution become acidic (check with litmus paper). Add 5 drops of FeSO4 0.1 M and 2 mL of 4 M H2SO4. When adding in the 4 M H2SO4, make sure the test tube in the position 45°, so that the sulfuric acid can flow through the wall of test tube and form a different layer at the bottom part of the test tube. Results : NO3- solution after adding H2SO4 becomes acidic and is checked by litmus paper and has turned into red colour. Clear solution is obtained at the bottom of the test tube. What is the Chemical equation involved and Discuss the Nitrate test?
11. A tank contains 40 gal brine for which the concentration is initially 3 lb/gal of salt. A brine solution is pumped into the tank at the rate of 5 gal/min. and the mixture, kept uniform by stirring, runs out at the same rate. If the concentration of the solution flowing in is 2 lb/gal, a) determine the amount of salt in the tank at anytime t, b) how much salt is present after 10 min? c) after a long time?
do both plzz or else skip do not give incomplete solution plz
1. Aspirin could be recrystallized by dissolving in ethanol and adding water. Explain the logic for this procedure.
Molar concentration of the bleach stock solution: .134 mol/L Solutions(Dilutions) Concentration% Experiment 1 0.25 Experiment 2 0.50 Experiment 3 1.0 Fill in the OCl- molar concentrations for each experiment. Solutions(Dilutions) OCl- Concentrationmol/L Experiment 1 Experiment 2 Experiment 3
part A 1. Concentration of Known NiCl2 Stock Solution ___500________ mM Tube Number Blank #1 #2 #3 #4 #5 2. Volume of Known NiCl2 Stock Solution Pipetted Into Tube 0.00 mL 1.50 mL 3.00 mL 4.50 mL 6.00 mL 7.50 mL 3. Volume of Distilled Water Pipetted Into Tube 11.00 mL 9.50 mL 8.00 mL 6.50 mL 5.00 mL 3.50 mL 4. Total Volume of Solution In Tube 11.00 mL 11.00 mL 11.00 mL 11.00 mL 11.00 mL 11.00 mL 5. Diluted Concentration of NiCl2 In Tube ----------- 68.2 mn 136mn 204mn 273mn 341mn 1. Equation for the Best-Fit Straight Line Y=3822x+4.7446 2. Absorbance at λmax for Diluted Unknown 0.87 3. Concentration of NiCl2 in Diluted Unknown 25.693 mM Determine the dilution factor for your diluted unknown U1 based on how you prepared the solutions in Part A. Record this on your report sheet in Part D #4.
Calculations: a) Average the two closest burette readings. Average all three readings if they agree within + 0.25 ml. b) Write the chemical equation for the reaction of acetic acid with sodium hydroxide. c) Calculate the amount (in moles) of sodium hydroxide that you needed to reach the equivalence point. Then calculate the concentration of acetic acid in the vinegar. d) Find the molar mass of acetic acid. Then calculate the mass of acetic acid in the volume of vinegar you used. e) The density of vinegar is 1.01 g/ml. Calculate the mass of the vinegar you used. Then find the percent (m/v) of acetic acid in the vinegar. Discussion: a) Compare your results with other students. What can you conclude about the concentration of vinegar you and the rest of the class used? b) Discuss how accurate you believe your results to do and any possible sources of error. c) Phenolphthalein was used as an indicator. Why should we place the vinegar, rather than sodium hydroxide, in the Erlenmeyer flask?…
Please provide correct solution.
What is wrong with this setup? buret acid of unknown concentration base of known concentration stopcock The buret needs to be filled with more base The tip of the buret is not placed inside of the flask The buret is not supported by clamp Nothing is wrong with this
4. The Ksp for MgCO3 = 1.1 x 101º. CIRCLE the solubility of MgCO3 in pure water. a) 1.1 x 10-10 M b) 1.1 x 108 M c) 1.1 x 107 M d) 1.1 x 106 M e) 1.1 x 10$ M
Chemistry Which lab technique(s) can be performed on solid, somewhat soluble samples? Melting Range Determination or Recrystallization. Melting Range Determination. Not Recrystallization. Neither Recrystallization nor Melting Range Determination. Recrystallization. Not Melting Range Determination.