If you have a closed system that is filled with water on 2bar, the pump is selected for pressure losses due friction of the pipes(1bar) 1/ why don't we have to take pressure losses due height in account? 2/ what is the pressure at 100 m height inside the system? When the pump stops? And when the pump is circulating, prove your answer

Q: A cylinder shown in fig. has diameter (25mm) height (300mm) and relative density (R.D=7.85). The…

A:

Q: Determine the direction of flow through the tube shown in Fig. 4, in which y 50 ib/ft', u = 0.40 p .…

A:

Q: mp while the volumetric e

A: Volume, V= 50 m3 Time, t = 5 min Length, L1 = 5.2 m Length, L2 = 2.2 m Efficiency, ηpump = 95%…

Q: Q2/ Water have a surface tension of 0.4 N/m. In a 3 mm diameter vertical tube if the liquid rises 6…

A:

Q: A container is filled with a liquid of density p. The surface of the liquid is at atmo- spheric…

A: The expression is obtained using Bernoulli's principle.

Q: A simple rainwater collector used for home garden use is show below. It is comprised of an open-air…

A:

Q: A simple rainwater collector used for home garden use is show below. It is comprised of an open-air…

A: Since you have asked a multi-part question thus we can provide you the solutions to the first three…

Q: garage lift has a 52 cm diameter piston supporting the load. Compressed air with a maximum pressure…

A:

Q: Given a system as shown in the following figure. Calculate the water level difference between two…

A:

Q: The figure below shows a liquid-level system in which two tanks have cross-sectional areas, A₁ and…

A: To Find:A. The differential equation model for the system behavior in terms of the liquid heights…

Q: 3. A spaceship lands on a planet where the atmosphere is completely made of water (p = 1000 -g). The…

A:

Q: In the system given in the figure, the top of the container and the pipe outlet are since it is…

A: Given- H = 151 m,h = 121 mD1 = 40 cm=0.4 m, D2 = 150 mm =0.15 m

Q: Example 4-6: The water flows through the pipe bend with a discharge of 200Ls. The bend is placed…

A: To Find:  The magnitude and direction of the force of water on the bend. Given : The discharge is…

Q: Find the value of pressure at dpeh of 2.4 m. Take density of water 1000 kg/m3

A: Given data : Acceleration due to gravity=g Depth=h Density of water=ρ   Required : Pressure

Q: A tanker contained with water is pushed horizontally at constant acceleration of 5.0 m/s?. If the…

A:

Q: 37. For a tank (T = 41 C°, volume = 0.051 m³, the rate change of density = 2.6 kg-m³-s*), through a…

A:

Q: Two pipes A & B carries an oil of specific gravities 0.9 & 1.2 respectively. The center of the pipe…

A:

Q: Billy flew from New York to Cincinnati and had a closed container with a closed outlet to drink…

A: Diameter of the container→DC=5 Cm=0.05 m Height of the container→HC=27 Cm=0.27 m Hence the initial…

Q: CAREFUL WITH UNITS !! a) Find the magnitude F and point of application y R of the water force on the…

A: To Find : Force F and its point of application. Given : The gate dimensions and gate depth. The free…

Q: 1. This figure shows three tanks that are connected to each other as a part of water storage…

A:

Q: A simple rainwater collector used for home garden use is show below. It is comprised of an open-air…

A:

Q: A 4-inch diameter cylinder moves a 25000 Ib load 24 inches in two seconds. Determine: a. The…

A: Given data,D=4instroke length L=24 inLoad =25000lbtime t =2s

Q: Find the pressure at depth of 33 m below free surface of water in reservoir

A: Given data : Depth (h)=33 mDensity of water (ρ)=1000 kg/m3Acceleration due to gravity (g)=9.81 m/s2

Q: 03: Answer ONE Section only. a. Three reservoirs are connected, if pipe (1) and pipe (3) having…

A:

Q: a conical water tank has its top at ground level(considerr this to be the x-axis) and its base 12 ft…

A:

Q: d, is fitted to the outlet pipe of a pump with diameter D. Let h; be the height of the section 0-0…

A:

Q: A tank, shaped like a cone has height 8 meters and base radius 3 meters long. It is placed so that…

A: The height of cone is The radius of base is The density of water is

Q: Find the gage pressure in the water pipe shown in fig. Not's: the density of water =1000kg/m', S =…

A: As per given question Find the gage pressure in the water pipe shown in fig.

Q: Q: A tank is shown figure below will be filled with water and the water drains by gravity from small…

A: Given: ro=3 cmCd=0.65L=2 mR=0.3 m

Q: Restitution coefficient through the measurement of the height of the bounces of a bouncy ball, find…

A:

Q: Two pipes A & B carries an oil of specific gravities 0.9 & 1.2 respectively.  The center of the pipe…

A:

Q: For a tank, calculate the volumetric flow of water, which comes out through a pipe, the tank is…

A: Given: Height of the tank: →h=2 m Exit diameter of the pipe: →Dexit=0.05 m So the cross sectional…

Q: Q.2: Calculate the pressure difference in sections (1) and (2) to the system in the figure. Will…

A:

Q: Discussion: 1-The thrust force increases with increasing depth of immersion, and the relationship…

A: Hydrostatics Law: According to Hydrostatics Law, the pressure in a vertically downward direction in…

Q: best fits between the options of the graph A, B, C, D and F,

A: Given:- Static head= 85 Capacity= 195   To Find:- Best impeller & Expected Power consumption

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.