If x(t) = 13cos2t + 5sin 2t and y(t) = 15cos(2t – 11.8°) what is the phase difference?(Both must be expressed in cos term)O 219.2None of the answers6.2A Moving to another question will save this response.MacBook Pro80F3FIF2F4F673541118#33r2$48&50677V8Aоо

Answered: Image /qna-images/answer/4895c025-e90b-4e06-bf9e-7c5ae33ff4c9.jpg

If x(t) = 13cos2t + 5sin 2t and y(t) = 15cos(2t – 11.8°) what is the phase difference? (Both must be expressed in cos term) O 21 9.2 None of the answers O 6.2 L» A Moving to another question will save this response. MacBook Pro 411

If x(t) = 13cos2t + 5sin 2t and y(t) = 15cos(2t – 11.8°) what is the phase difference? (Both must be expressed in cos term) O 21 9.2 None of the answers O 6.2 L» A Moving to another question will save this response. MacBook Pro 411

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the equivalent resistance of the cirucit below
ANGLE 30° 60° 90° 90/38cm 90/38cm 90/76cm 90/114cm 90/152cm 90/185cm 90°/215 SHADING % 10% 50% 100% 0% 10% 20% 30% 50% 80% 100% IRRADIATION 45.79 34.70 52.79 86.96 85.56 107.1 107.3 46.02 65.26 99.76 VOLTAGE 19.21 19.53 19.19 19.52 19.14 19.11 19.27 19.42 19.53 19.65 AMPERE 0.015 0.017 0.016 0.021 0.022 0.022 0.022 0.022 0.024 0.024 POWER 0.288 0.346 0.323 0.411 0.432 0.426 0.426 0.444 0.484 0.471 In table. At what percentage of shade that current, voltage and power reach the minimum a. output? Explain your answer? b. In table. Record the result of this shading effect on the output of a solar module? c. In your own conclusion, in table. What is the effect of shading to the efficiency of the performance of the PV cell with regards to Voltage, Current and Power? Explain
C1 L1 R1 V1 Vout V1 contains the fundamental and its harmonics (fo, 2fo, 3fo, ...). The amplitude of the harmonics is inversely proportional to the harmonic number. V(fo) = 10 mV V(2fo) = 10mv/2 = 5 mV V(3fo) = 10mv/3 = 3.33 mV V(4fo) = 10mv/4 = 2.55 mV a) What is the minimum value of Q for the circuit that will attenuate the third harmonic (3fo) in Vout to be less than 1% of the fundamental? b) What is the amplitude of the fifth harmonic (5fo) as a percentage of the fundamental?
2 535289806977814... For the circuit shown below, detemine the voltage of the -j10 2 capacitive reactance. -j5 2 ILOA(1 #jlon js a < 1012 0.5L-90 542 A
i need the answer quickly
The figure below shows a phase shift oscillator with amplitude control. Design the circuit to produce 7kHz frequency and a ±8V output waveform. Assume that I1 = 1mA and R2=R3. Do your design on a piece of paper and then enter the various resistor and capacitor. NOTE: Use only E24 values for your design Enter the values of R1=_____Ω, R2_____kΩ . , R3._____kΩ , R4._____kΩ . , R5_____kΩ , R6_____kΩ and R7 _____kΩ and the value of C=_____ μF
Channel 1 and Channel 2 Time (ms) Phase problem. In the above figure the time base is 1 ms/div, what is the period of the signal from Channel 1 in ms? What is the phase difference (in degrees) between the signals in Channel 1 and Channel 2? ms, _degrees Voltage (arbitrary units)
(iii) Determine the value of RL for the maximum power transfer, Pmax to occur and calculate the maximum power transfer, Pmax,
1%AV . Ili. N M 4 1.:YA docs.google.com a حضور الطالب Required السؤال الخامس Answer the following BJT with VCC=10v, RC=9.8Kohm, B=100 and RB=200Kohm. VBB=D ? * O 1.3V 2.7V 2.857V O 2v Page 7 of 7 Back Submit Never submit passwords through Google Forms. This form was created inside of Al-Furat Al Awsat Technical University. Report Abuse
is lespons Quèstion 7 If charge is placed at minus infinity, its potential is infinite None of these P Type here to search
Give solution/explanation for letter i only. Answer Capacitive, 8.4883?FSubquestion/s are given with their corresponding answers. A pure element is connected across an AC signal. CH1 and CH2 measures the voltage and current respectively:CH1 (Yellow) SettingsVolts/Div: 50VTime/Div: 5msProbe Settings: X1CH2 (Blue) SettingsCurrent Probe Ratio: 100 mV/mAVolts/Div: 20VTime/Div: 5msProbe Settings: X1If ?? (distance between two ‘purple’ cursors) is 5ms, determine:a. Periodb. Frequencyc. Phase Angle Differenced. CH1 Peak Voltagee. CH1 RMS Voltagef. CH2 Peak Currentg. CH2 RMS Currenth. Impedance of the pure elementi. Type of load. If reactive, indicate the values of inductance or capacitance a. 20 msb. 50 Hzc. 90°d. 150 Ve. 106.066 Vf. 400 mAg. 282.8437 mAh. 375 Ωi. Capacitive, 8.4883?
HH 9 0btoin the tronsfer functle Vout Vin R. ) Whot is the C. Volue to place gero frequency to 206H2? Vout c) What is the Ce volue to place pole frequer to 500k Hz? R2=1k2 d) Plot the frogueney response.