If W-100 N and u-0.5, then the friction force of the block shown in figure is

Q: When a force of 500 N pushes on a 25 kg box as shown in the figure, the acceleration of the box up…

A: Givenforce acting on box P=500Nvertical and horizontal components of force P on inclined surface…

Q: A tank of water sits on a cart with frictionless wheels as shown. The cart is attached to a mass and…

A: Given data: The coefficient of static friction of the mass with the ground is µ = 0.50.  The…

Q: In the figure below, the weight of the block is 300 kg and the angle of internal friction is 24.2…

A:

Q: From the given figure, the mass of the block is 200kg. Coefficient of friction for all surface is…

A:

Q: Find the weight W in the given figure to Cause the weight w impending if the motion of down the…

A: Given Weight = 500 N Coefficient of friction = 0.29 To find Magnitude of W

Q: 100 N 400 N

A:

Q: A 360-kg block is resting on a 23 deg inclined plane with a coefficient of friction = 0.47. Find the…

A:

Q: 300 lb 30° AT 40 lb T 300 lb 34P Sürtünmesiz makaraların olduğu yukarıdaki sistemde her iki tarafa…

A:

Q: a 2kg book is pushed against a vertical wall by a horizontal force P. The coefficient of friction…

A: As per given question A 2kg book is pushed against a vertical wall by a horizontal force P. The…

Q: A 190-kg block is resting on a 58 deg inclined plane with a coefficient of friction = 0.59. Find the…

A: Given                      Mass, m = 190 kg                         Angle = 580 Coefficient of…

Q: A 140-kg block is resting on a 25 deg inclined plane with a coefficient of friction = 0.83. Find the…

A: Given: m =140 kg θ=25o μ=0.83

Q: A trolley weighing W₁= 306.1725 N, a crate with Wc= 612.345 N, is being transported along a smooth…

A:

Q: Q. A body of 2000 N is placed on a horizontal surface as shown in Figure below. Determine the…

A:

Q: The block A in the figure supports a load of 800N and is to be raised by pushing the wedge B under…

A: we will draw the FBD of A and B separately. FBD of A will give us R1 and R2 FBD of B will give us R3…

Q: Problem4 A person is moving a 250N box as shown in the figure below. He is pulling the box at an…

A:

Q: A block Rof mass 100 kg is placed on a block Sof mass 150 kg as shown in the figure. Block R is tied…

A: Given: Mass of block R, mR=100 kgMass of block S, mS=150 kgcoefficient of fricition, μ=0.4

Q: The figure shows a pair of pin-jointed gripper-tongs holding an object weighing 2000 N. The…

A: Answer: The magnitude of force F required to hold the weight is 5000 N.

Q: The block shown in the following figure has a weight W equals to 75 lb and subjected to the action…

A:

Q: The block of weight W = 10 kN is pulled by the force P inclined at the angle 0 = 15° to the…

A:

Q: A screw jack is used to lift a load of 30 kN. The screw of the screw jack is square threaded with…

A: The solution is given below

Q: Shown in the figure below is a magazine resting on top of a book. There is static friction between…

A: given:

Q: 1: A cylinder of (75N) weight, (r=65cm) is to entrust to a horizontal surface its coefficient of…

A: Given data Weight = 75N Radius = 65cm Coefficient of friction = 0.4 Moment = 5625 N-cm

Q: A block weighing 4500 N resting on a horizontal surface supports another block of 3000 N as shown in…

A:

Q: Two bodies is connected in point C, are supported by rigid underlay at an angle α. F is the force…

A: Given that, G1=160 N,G2=10 N,α=30°,L=2000 mm, (a) When the arm is slipping, then there will be no…

Q: A person is pushing on a uniform block of wood as shown in the figure and parameter table. The block…

A: Given: mass of the wood=140Kg coefficient of static friction of wood(μw)=0.25 so the weight of the…

Q: The component of the force along the inclined plane due to mass of the body on a  inclined plane is…

A: Given data: Component of the weight of the body along the inclined plane, Fx = 500 N. The net force…

Q: A 260-kg block is resting on a 29 deg inclined plane with a coefficient of friction = 0.68. Find the…

A: FREE BODY DIAGRAM is a diagram of the system which represents all the forces acting on the system.…

Q: A person is pushing on a uniform block of wood as shown in the figure and parameter table. The block…

A:

Q: Blocks mj and m2 are connected by a rope as shown in the figure. There is friction between mi and…

A: Knowns; μs, n2, m1, g, and θ Unknowns; P, m2, Ff, and T The FBD of mass m1 is; The FBDof mass m2…

Q: A 60 Kg crate is resting on top of a 45 Kg crate as shown in figure below. The top crate is attached…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.