If the twe inputs of tha multiplier in thefeedback path are tied boyether as shown in Fig (3-40),squre-root circuit » will be achieved.then aFor this circuitVinVo =-k VeVinVinVo =or k=Vin%3DFigl340) squre-rootFor K positive, thecondition of stable linearcircuitoperation i's Vin must benegative and henceVoVinl(3-27)%3D

Answered: Image /qna-images/answer/3f044b36-c4bc-4dfa-903e-d3fa8fef5c51.jpg

If the twe inputs of the multiplier in the feedback path are tied toyether as shown in Fig (3-40), than a squre-root circuit will be achieved. >> For this circuit Vo = - Vin k Ve Vin Vinl or Vo = Vin For K pasitive, the condition of stable ligear Figla.40) squre-root circuit operation is Vin must be negative and hance Vo = Vinl (3-27)

If the twe inputs of the multiplier in the feedback path are tied toyether as shown in Fig (3-40), than a squre-root circuit will be achieved. >> For this circuit Vo = - Vin k Ve Vin Vinl or Vo = Vin For K pasitive, the condition of stable ligear Figla.40) squre-root circuit operation is Vin must be negative and hance Vo = Vinl (3-27)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please solve this question in control system quickly
i need the answer quickly
2. The circuit given below has ß-200 R₁=59.5kQ; R₂=14.88kQ;R3=1kQ and R4=0.1kQ, Identify the feedback type and configuration and calculate the following: Open loop gain (A), feedback factor ß and closed loop gain (Af). Vi Сс www www R₁ R₂ 5 V I R3 R4 www · www Cc HH Vo
H.W 1 Design produce an output given by Vo= 2V₁-5V₂-5 5 Sv₂dt an ор-Атр Op-Amp circuit that
b. use nodal analysis to solve
Q2) For the circuit shown in the figure, calculate the input resistance for each step and find the overall voltage gain in dB. Assume Bpc = 100 and Bac = 150 Vce +12 V Rc 2.2 k2 R 5.6 kfN R1 56 kN R4 22 k 330 E RE Vin o R2 12 k2 RE 1.0 kN
2. Non-linear feedback elements are quite common as we will observe later this semester. The non-linear circuit in the feedback network shown is called an analog multiplier. The terminal characteristics of the analog multiplier are defined as shown in the figure. Show that this circuit can be used an analog signal divider. That is derive Vo in terms of Vs1 and Vs2. R2 Multiplier Vs2 R1 Vs1 Va Multiplier V = KVa V6 11-1-1-110l 10I ..... ...... ... DID
R, OV OUT + Complete the analysis showing that Vo/Vin = -Rf/Rin Let currents be defined as 1 equals the current flowing through Rin from left to right 12 equals the current flowing into the Opamp 13 equals the current flowing through the feedback resistor from left to right. Write the KCL equation in terms of 11, 12, and 13 at the inverting node of the Op-Amp. O There is no current flowing in the circuit O 12 = 11 + 13 O 11 = 12 + 13 11 + 12 = 13
(d) An instrumentation amplifier is used when the application signal is very low. For the circuit shown in Figure Q2(d), calculate the applied input vin of the circuit to get the output of 5V at vo. Let Rr=360k 2 and R₁ = 12k 52. Rf www R1 Vec www Vo -Vec Figure Q2(d) (e) Illustrates instrumentation system for temperature measurement with the help of block diagram. Vin uA741
Subject: Analog Electronic and Circuit Please Solve this question
Note: Answer all questions Questions' marks B The parameters for the summing amplifier in Figure below are: Rp 100 kl, and R3 The inpul voltages are ,=4+125sinwt mV and V=-6 mV. Determine R, and Rz to produce an output voltage of vo -0.5sinot V. i4 RI looKe ww Is. RF R1 V =0 i2 R2 Iu.あ R3 Ra 8.
HW: Find the voltage gain of the OTA circuit. HINT : io = gm*(Vp - Vn) value. It's characteristic of OTA R2 Important : Vp value is not equal to Vn value R1 V. in gm V. Vn URGENT! THIS IS NOT OPAMP CIRCUIT. THIS IS OPERATIONAL TRANSCONDUCTANCE AMPLIFIER. (OTA)