If the resultant force between the two forces acting on the hook is 12.5 kN, determine the angle between the resultant and the vertical. Take F₁ as 9.7 kN and F₂ as 5.6 kN.

Q: A horizontal compass is placed 19 cm due south from a straight vertical wire carrying a 49-A current…

A: Step 1:  Given, Bearth = 0.45 * 10-4Twe have Known that the formula for net magnetic field of the…

Q: Q1 The table below contains the cross - sections Areas of road Calculate the volumes of the earth…

A: Given; Distance (m) 0 30 60 100 140 Area (m2) 48 37.5 25.345 13.854 14.145

Q: A railroad curve has De = 4°00', I = 24°00', and PI station = 35+45.00 ft. Use the chord definition…

A: Approach to solving the question: Detailed explanation: Examples: Key references:

Q: Lloukle Inte gr ation Meth od Lletermine the ff :). LDefle etion at e). Mope at C

A:

Q: Determine Qmax [Qmax = 6.48 x 10-4 m

A: To find Qmax

Q: Stations are measured by means of a Gunter’s chain (66 ft) which was 0.4 links too short and the…

A: Given Data -  L = 100 fte = -0.4 linksL' = L+e = 100-0.4 = 99.6

Q: 30 15 050 What are the commands needed to solve this ?question in AutoCAD Ø100 8x 010 ON PCD 80 23…

A: To Determine Commands needed to draw the given image in AutoCAD.

Q: Analyze completely the following by method of members. Make a summary of the answers.

A:

Q: Calculate the area (in sqm) of the cross-section of ranges DF. (Type your answer using 2 decimal…

A: To determine Area of section Df

Q: 2. Compute for the moment of inertia about xo and yo of the following figures. a) b) 100 mm 100 mm…

A:

Q: 3. Calculate the moment of inertia of the shaded area about the x and y axes. 100 + 100 50 50 -75 75…

A: Concept Here we will use parallel axis theorem to calculate the moment of inertia.

Q: 3. Calculate the moment of inertia of the shaded area about the x and y axes. 100 + 100 50 50 -75 75…

A:

Q: A plot with the shape of a trapezium has the following measurements Long side: 52 m Short side: 24 m…

A: The given data is shown below: Trapezium"Long side=52 mShort side=24 mPerpendicular…

Q: (a) Consider two points on the equator at coordinates (latitude, longitude) of (0°N, 20°E) and (0'N,…

A: We use the Haversine formula to find out the great circle distance between two points (ϕ1,λ1) and…

Q: If the collar at A is fixed to the member and can slide vertically along the vertical shaft which…

A: Hi there! you haven't mentioned your ID so, I have taken the values of A and Y from the given…

Q: Question 6 6. To find the distance across a small lake, a surveyor has taken the measurements as…

A:

Q: Find the forces (kN) on the members of the given truss. Determine also the magnitudes of the support…

A:

Q: when e/D is 0.00025 what is reynold numbe

A:

Q: Q.2. check. If there is an error please distribute it to the elevations. E = 40* K Please calculate…

A: Levelling is the procedure of comparing heights of points on the surface of earth. It is important…

Q: Q3: The polygon traverse ABCDEA shown in figure 2. is to be divided into two equal areas by a…

A: If polygon vertices are(x1,y1), (x2,y2), ............... (xn,yn)then areaA =…

Q: There is a table of an observed plane triangle ABC but some parts are missing. Please fill up the…

A: To complete the table, we need to calculate the numerical correction and the rounded correction for…

Q: Point A is between points B and C. The distances of B and C from point A are 1000m and 2000m…

A:

Q: Q2The areas within the contour lines at the site as follows: Calculate the volume of water between…

A: Given Above contours and the area between them

Q: Question 2: Locate the centroid of the following area. 3 in 12 in 3 in 2 in ■ 2 in 5 in 4 in 4 in 2…

A:

Q: The following is a page of an old level field book, in which some of the missing entries are shown.…

A:

Q: View Policies Current Attempt in Progress Find the given determinant by any method. 10 000 -61 0006…

A: The determinant is defined as a scalar value which is associated with the square matrix. If X is a…

Q: The coordinates of traverse stations of a closed traverse ABCDE are given below Station X (m) A 0 B…

A:

Q: QI/ An complet traverse table is obtaind as flowing ? Calculate 1. length of DA & bearing of AB 2.…

A: Let the length of DA be x and bearing of AB be θ a.) line length RB    θ Latitude…

Q: questions by completing the tabulation below. What is the computed departure of line DE?

A:

Q: Group A A pipe line was plotted on a map having a scale-1/2000. Its length on this map - 50cm. What…

A:

Q: Example 5: The followings are the F.B. of lines. Calculate their B.B. (1) AB N 18° 0' E 1 (2) BC S…

A:

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.