If the principal stresses on a material witha yield stress in shear of 200 MPa are02 = 175 MPa and o13D 350 МPа.,%3Dwhat is the stress, 03, at yieldingaccording to the Tresca criterion?50 MPa30 МРа(None150 MPa

Answered: Image /qna-images/answer/b74706d1-72b7-4002-806f-b20f749f3b15.jpg

If the principal stresses on a material with a yield stress in shear of 200 MPa are 02 = 175 MPa and o1 = 350 MPa., what is the stress, 03, at yielding according to the Tresca criterion? 50 MPa 30 MPa (None 150 MPa

If the principal stresses on a material with a yield stress in shear of 200 MPa are 02 = 175 MPa and o1 = 350 MPa., what is the stress, 03, at yielding according to the Tresca criterion? 50 MPa 30 MPa (None 150 MPa

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Related questions

Q: 1.10 Link BD consists of a single bar 1 in. wide and in. thick. Knowing that each pin has a -in.…

Q: What pressure should be applied to a lead block to reduce its volume by 10% (Bulk modulus of lead =…

A: A lead block has to be under pressure in order to have its volume reduced by 10%..

Q: Frem the tensile stress-strain behavier For the brass specimen ,0 the diameter is 12-8 mm Calcalate…

A: Modulus of elasticity, =stressσstrainε=200-150 MPa0.1-0.064=1388.88 Pa

Q: A thin rectangular plate is uniformly, deformed, as shown. Determine the shear strain Yxy at P.…

A: Solution: The shear strain of the thin rectangular sheet in the y-direction can be obtained using…

Q: Given that, bz (400mm x 3000)mm b3(400mmx yootim) Area 100000mm? %3D 400 XB00 01200000 mm2 Ab3 =…

A: Write the relationship between stress and area. For constant force F, the stress σ is inversely…

Q: A copper wire 4 m. long has diameter of 1 mm, if a load of 10 kg. wt is attached at other end. What…

A: Solution:-Given thatlength of wire (L)=4 mdiameter of wire (d)=1 mm=0.001 mmass of Load (m)=10…

Q: 12mm dia 18mm dia. P=12 kN 2 m. 12mm dial 2. Three steel cable jointly support a load of 12kN. The…

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A: Calculate the stress in steel section.

Q: e plates in shear, what is the shear

A: We know, Shear stress=force/Area Given, Force=47kN Diameter=3.25mm Radius=1.625mm

Q: Based on the sign convention we are using, if we cut a beam and draw the left portion of the beam,…

A: Cutting a beam and draw the left portion

Q: A hollow shaft with an outside diameter of D=54 mm and an inside diameter of d = 40 mm is subjected…

A: To determine the shear stress on the element, we can use the torsion equation: τR=TJhere,τ=The shear…

Q: What is the magnitude of the maximum stress that exists at the tip of an internal crack having a…

A: See below

Q: Two wooden members of 70 x 110-mm uniform rectangular cross section are joined by the simple glued…

A: Given: ϕ=20°, L=110mm, B=70mm, τ=500kPa The uniform rectangular cross-sectional area of the wood is…

Q: 2.31. The three principal stresses at a given point are o=60 MPa, o2=-100 MPa, 03 =-10 MPa. If the…

A: Given: The principal stresses at a given point are 60 MPa, -100 MPa and -10 MPa. Introduction: The…

Q: If the applied load is 49 kN, determine the new diameter of the specimen.

A: Given:- G = 28 Gpa diameter of specimen = 12.5mm Gauge length = 50 mm Given diagram:-…

Q: material is applied by a tensile forces of 132 kN on a bar of the material with a cross- sectional…

A: stress is defined as the force per unit area. Write the expression for stress. S=FA…

Q: For the given state of stress, determine: (1) The principle stresses and the directions of the…

A: Solution:- 1). In the figure given we have: σx= 350…

Q: Determine the outside diameter of a tube if the stress is limited to 128 MN/m2 and a hollow steel…

Q: The beam consists of two S18 × 70 sections that are welded together as 15 kip/ft, calculate 5.70…

A: Given : wo = 15 kip/ft;

Q: P-1. A steel shaft 2 m long that has a diameter of 90mm. is subjected to a torque of 10 KN-m. Use G…

A: Given data d=90 mmT=10 kN-mG=200 GPa Here, d is the diameter and T is the torque. While G is the…

Q: A structural steel bar with a 3.6 in. x 0.890 in. rectangular cross section is subjected to a…

Q: 3. A flat steel bar 150 mm wide by 50 mm thick has axial loads applied at points A, B, C and D as…

A: Solution: The free-body diagram of the forces of the bar in section BC is shown in the figure.

Q: What is the area of the stock file if a 1.5 x 105 kg mass presses down 2.5 feet high stock file that…

A: Given that-Mass, m=1.5 × 105 kgDeformatio, ∆x= 2.7 cm=2.7×10-2 m=0.027 mHeight, h= 2.5 ft=2.5×0.3048…

Q: 1.18 A load P is applied to a steel rod supported as shown by an alu- minum plate into which a…

A: l=12 mm sheering stress=180mPa The Stress of an aluminum plate: 70mPA

Q: Suppose that a 6-mm diameter steel has a breaking stress of 5.5x108 Pa. What will be the diameter…

Q: A copper wire 4 m long has diameter of 1 mm, if a load of 10 kg. wt is attached at other end. What…

A: We need to compute-(a) extension (l)=?(b) Lateral compression=?Given that-Length of wire (L)=4…

Q: One end of a wire 2 m long and 02 cm in cross-section is fixed in a ceiling and a load of 4:8 kg is…

Q: If the Junk modulus of Y is 160GPA and the shear modulus of elasticity is 0.25Y, what is the value…

Q: What pressure is required to reduce the volume of a lead block by 1% ? (Given : Bulk modulus of lead…

A: Description : In this question we have to find the pressure required to reduce the volume of lead by…

Q: An endüviye collector step (multiplicity coefficient) with 4-Pole, 10-cavity and 20-slice collector…

A: collector step (multiplicity coefficient) with 4-Pole, 10-cavity and 20-slice collector will be +2

Q: A cylindrical specimen of a nickel alloy having an elastic modulus of 207 GPa and an original…

A: Given Elastic modulus, E = 207 GPa Original diameter, D = 10.2 mm = 0.0102 m Tensile load, P =…

Q: What shear stress is needed to produce a shear strain of 2.50 x 10-5 on an aluminum block?

A: shear modulus=shear stressshear strainshear stress=shear modulusshear strain

Q: 213. The rigid bar AB, attached to two vertical rods as shown in the figure, is horizontal before…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set bys =…

A: s = 350 ×106 Nm2ε = 0.010

Q: Assume if the shear stress in steel exceeds about 4.00 x108 N/m2 the steel ruptures. Determine the…

Q: The stress experienced by a certain surface is 17612Pa when a 17-N force is applied to it. How much…

Q: A steel beam is placed vertically in the basement of a building to keep the floor above from…

Q: For a bronze alloy, the stress at which plastic deformation begins is 295 MPa and the modulus of…

Concept explainers

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).

Question

If the principal stresses on a material with
a yield stress in shear of 200 MPa are
02 = 175 MPa and o1
3D 350 МPа.,
%3D
what is the stress, 03, at yielding
according to the Tresca criterion?
50 MPa
30 МРа
(None
150 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

A square flat plate of dimensions 1 m x 1 m is moving with a maximum speed , U causing a fully laminar motion of it inside air ( density :1,2 kg /m3 viscosity :1.5x10-5 m2 /s ) Determine the magnitude of Shearing Stress on the surface of the plate SS=? at plate's trailing edge.ANSWER:SS= 0,0317 Pa
An aluminum bar AD has a cross sectional area of .40in^2 and is loaded by forces P_1=1700lb, P_2=1200 lb, and P_3=1300lb. The length of the segments of the bar are a=60in, b=24in, and c=36in. length when all three loads are applied? A PROB. 2.3-3 Ç a B Show Transcribed Text P₁ C P₂ ←P3 D Question: By what amount P should the load P_3 be increased so that the bar doesn't change in length when the three loads are applied.
Member BC has a square cross section. The diameter of the pins at A and B are 3 cm and 2 cm respectively. If the allowable normal stress for member BC is allow = 25 MPa and the allowable shear stress for the pins iS Tallow = 12 MPa, calculate the maximum force intensity w (in N/m). 4 cm В 50° 3 m A W
2. An overhanging beam having a span of 8 m has its overhang 2 m from both ends. The beam carries a uniformly distributed load of w KN/m over the entire span of the beam and a concentrated load of 5 KN at 1 m from the left support. If the beam has the cross section shown and the allowable horizontal shearing stress is 80 MPa, what is the safe magnitude of the load w? 10 my fri L: 10 mm 50 mm T 50 mm 10 mm
A 195-kg load is hung on a wire of length of 3.80 m, cross-sectional area 2.00 10-5 m2, and Young's modulus 8.00 1010 N/m2. What is its increase in length? ______mm
A copper wire 4 m. long has diameter of mm, if a load of 10 kg. wt is attached at other end. What extension is produced, if Passion's ratio is 0.26 ? What is lateral compression produced in it? You = 12.5 × 10¹⁰ N/m².
What is the axial stress in the bronze rod (in MPa)? 2m 3m 60 KN Usmm I5 mm banze rod Next
1. Consider the brass alloy for which the stress-strain behavior is a cylindrical specimen of this material 10.0 mm in diameter and 101.6 mm long is pulled in tension with a force of 10,000 N. If modulus of elasticity is 85 GPa compute the specimen elongation
A tensile test specimen has a gage length = 3.0 in and diameter 0.75 in. Yielding occurs at a load of 38,000 lb. The corresponding gage length 3.01 03 in (neglect the 0.2 percent yield point). The maximum load of 54,000 lb is reached at a gage length 3.453 in. If the specimen necked down to a diameter 0.645 in, determine the percent reduction in area (round to the nearest whole %). 40
A tensile test was conducted on a steel bar. The length of the bar was 10 cm and the extension was 2 mm. What will be the % strain produced. Select one: a. 0.02 b. 2 c. 0.002 d. 0.2
A metal plate has an area of a face 1 m x 1 m and thickness of 1 cm. one face of larger area is fixed and a tangential force is applied to the opposite face. The displacement of the edge cm. Find the produced thereby is 0.005
An upright beam supports a load of 3,000 N and 2,500 cm long. The beam is compressed 200 mm by aload. Young’s modulus of the beam is 1.0x10 11 N/m 2. Calculate cross-section area of the beam.