If the Pico is plugged connected to a computer by a USB cable, what voltage(s) should you read on pin 40 and pin 36, respectively? OV (or Gnd) 5V and 3.3 V 3.3 V and 5 V Something in between 1.8 V - 5.5 V 3.3 V Undefined

If the Pico is plugged connected to a computer by a USB cable, what voltage(s) should you read on pin 40 and pin 36, respectively? OV (or Gnd) 5V and 3.3 V 3.3 V and 5 V Something in between 1.8 V - 5.5 V 3.3 V Undefined

A+ Guide to Hardware (Standalone Book) (MindTap Course List)

9th Edition

ISBN:9781305266452

Author:Jean Andrews

Publisher:Jean Andrews

Chapter5: Supporting The Power System And Troubleshooting Computers

Section: Chapter Questions

Problem 2TC

See similar textbooks

Similar questions

if you are using a dialup connection with 55000 bps channel ,then how many times use to upload a (2MB)word file?
Please give me correct solution.
the following protocol used to Synchronous serial interface Select one or more: a. interface medium-speed 1/0 devices b. interface low speed peripheral devices c. interface a digital to analog converter d. measure the amplitude of analog signals e. secure digital card
A microcontroller is used to interface an AC load through a relay. L1 20V U1 RAOC12NO-AND RAIC1NJANT RCCTPLSPIACOPITSOANI4 RAZCZNANDDACOUTIVREF. RASCINANDVRE RAACIOUTSRGTOCH RASK2OUTSRNOSSIALVOANA RASICLKOOSC2 RATCLOSCI RC1P2ACCP26osa D1 RCSOISCLIANIS SV RCASDISDALANI6 RCSSDOLANI7 RCBTXICKTONI OE R2 22 220V AC 200 RDICCPASD2SDAAN21 21 ROOEAN2 REONTOFLTOSRANI2 RB1NTIC12N3-JAN1O REONTICTED1IAN REOCTEDOPRAJOCP2C12N0ANG 10K Q1 2 ROP2CISSAN23 20 RDAP2DISDORAN24 ROGPICITKZIOKZIANCS RBSKOCIPSACCPITICHITIOANI REGAOCZPOC R1 10K PEDPJACOPSIANS www.studenteompanion.co.za REIPBIANE 10BEZCOPSIAN7 MOLRIVPPRE) RESET www.studentoompanion.ne 1. List the different types of interfacing used in this circuit? 2. What is the role of D1 and Q1? 3. Can the 220V AC source affect the microcontroller? Why? 4. What is the current gate of transistor Q1 (VBE is 0.7)?
Which of the following DMA Transfer Modes is the worst in term of hardware cost: a.Cycle Stealing b.Block Transfer Mode c.Burst mode d.Transparent mode
Your friend has just bought a new personal computer. She tells you that her new system runs at 1GHz, which makes it more than three times faster than her old 300MHz system. What would you tell her? (Hint: Consider how Amdahl’s Law applies.)
A brand-new computer monitor has been thoughtfully given to you by your great-aunt and -uncle. You immediately discover that none of the ports on the back of your computer will support the connection that is at the other end of the monitor's cord as you attempt to plug it in. What precisely will you do after that?
After interfacing an MCP4822 DAC to an ATTiny85, write a program so that it produces 2.5V on the DACS pin 8. Comment each line of code. Once you connect two active high pushbuttons and interface them to the ATTiny85, write a program that when pressing one button, it decreases the DAC's voltage by 0.1V. The program should also have it to when the other button is pushed, the DAC's voltage should increase by 0.1V. Comment each line of code.
Help. .In the output interface of the parallel port, along with the valid signal .............. is also sent.
Your great-aunt and -uncle have thoughtfully gifted you a brand-new computer monitor. As you try to plug it in, you immediately find that none of the ports on the back of your computer will support the connection that is at the other end of the monitor's cord. What steps will you take next, exactly?
One of these statements is false in terms of the I/O channels types: a.selector channel transfer data in parallel b.multiplexor channel selects more than one I/O device simultaneously. c.none of the above d.multiplexor channel transfer data in parallel
Which input port in the circuit of the Figure below is selected for input operation if the address within the I/O space is 1F03H? Required to answer. Single choice. A. Port 0 B. Port 1 C. None of the port is selected by this address D. Any port can be selected by this address E. Port 2