If the outlet of the condenser (stream 5) is fully condensed, what is the enthalpy of this stream? Assume Q = 0 and change in KE = 0 (1)(2)(3)(7)boilerturbine Amixer187.96 deg C13 МPа570 deg13 MPа230 deg C1.2 MPa1.2 MPаsat. liquid(4)(5)(6)condenserpump Aturbine BT = ?T = ?T= same as (5)22 kPa22 kPa1.2 MPa0.9 qualitysteamW= -1989 kW15 MPаpump B

Answered: Image /qna-images/answer/63c76d20-3db3-4b64-8576-fcafb71a3720.jpg

Answered: If the outlet of the condenser (stream…

If the outlet of the condenser (stream 5) is fully condensed, what is the enthalpy of this stream? Assume Q = 0 and change in KE = 0

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pure water flows through the cross section of the pipe 0.3m long and 3cm in diameter. The water entering the pipe has a flow rate of 373 K, 0.2 MPa to 2 kg/s. The discharged water also has a flow rate of 2 kg/s. At this time, the temperature is 373 K and the pressure is 0.195 MPa. Under this condition, the density of water is 961.5 kg/cm3. Find what was done at the entrance and exit of the pipe (J/s). Pay attention to the sign.
You are designing a system to mix fuel and air prior to ignition in an engine. Do you want the flow to be laminar or turbulent? Why?
CO2 gas enters the pipe at a flow rate of 2 kg / s, 3 MPa pressure and 500 K temperature. While the CO2 pipe type is flowing, it is cooled down at constant pressure and its temperature drops to 450 K at the pipe outlet. Find the ideal gas using the equation.
A counter-current extractor is employed to extract oil from a solid meal using ethyl ether as the solvent. The fresh meal is charged to the unit at a rate of 1000 kg/h and contains 25.0% (weight) oil. Pure solvent enters the bottom of the extractor. The overflow from the unit contains 60% (weight) oil. The underflow contains 0.25 kg of solution per kg of oil-free solids and the concentration of oil in the underflow is 12%. Calculate the following: a. The amount of solvent b. The percentage oil recovery
You are designing a piping system to facilitate the transfer of water from one industrialprocess to the next. You need the water to condense from saturated vapor to saturatedliquid at a constant 1000 kPa as it flows through the piping system. The pipe is to be madeof plain carbon steel with thermal conductivity ? = 60 W m-K⁄ and inner and outer radii?? = 5 cm and ?? = 7 cm, respectively. The thermodynamic property table at the end of thisproblem will be helpful throughout your analysis.a) If the convection coefficient between the steam and inner wall of the pipe is “verylarge”, what is the temperature of the inner pipe wall along its entire length?(Hint: Isobaric phase change is also iso___?)b) The fluid surrounding the pipe has temperature ?∞ = 30°C and the convectioncoefficient from the pipe to this fluid is ℎ = 100 W/m2⋅K. What is the heat transferrate out of the pipe, per unit meter of pipe? You may neglect radiation effects. Usea thermal resistance network in your analysis.c) The…
Wastewater containing lead is being released from a certain industrial plant. The stream contains X.YZ % Pb and is treated in a unit (maximum capacity = 5000 kg wastewater/hr) that removes 90% of lead in the feed, which is then recycled back into the plant. Another stream from the unit is being released to a lagoon. If the stream leaving the plant has a rate greater than that of the treatment unit. the excess of the capacity of the unit (say, the excess above 5000 kg/hr) bypasses the unit. This excess is combined with the liquid leaving the treatment unit, which is released into the lagoon. The treatment plant releases 7500 kg/hr of wastewater. Let X.YZ be 7.23 Calculate the mass fraction of Pb in the waste lagoon stream. Express your answer in 4 decimal places.
Answer the following questions O of O points Q1* Ql: In a steam power plant, steam enters at 8 MPa and 600 C, the condenser pressure is 8 kPa, and the net power out of the plant is 100MW. Determine 1- The enthalpy at point 1 P2
CO2 is needed in a surgical suite for abdominal laparoscopic surgery. You have already designed a nozzle to step down the pressure from the gas cylinder to the delivery hose. The well-insulated delivery hose has a 2.2 mm inner diameter. The inlet conditions to the delivery hose are 103 psia and 17°C. Typically, the surgeon uses 4 to 6 L/min of gas at pressures between 10 to 20 mm Hg to inflate the peritoneal cavity; however, the delivery system must be able to provide flow rate of 17.5 L/min at 20.0 mm Hg for safety. The surgeon will use a pin valve to control the flow rate and maintain the operating space. The gas temperature should not be any colder than 10°C when delivered to patient, or tissue damage might occur. Determine the acceptable delivery hose length to meet the surgical criteria. State assumptions.
Define each enthalpy obtained from tables and chart and draw the p-h diagramlabeling the respective evaporating and condensing pressures andtemperatures in each problem. Use the book, refrigeration and air conditioning 3rd edition hipolito b. sta. maria
What is the enthalpy of refrigerant 134a with s = 0.94190 at 0.85MPa? (Superheated Vapor)